Nissan Qashqai J11. Manual — part 1496
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SEC-283
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000010338082
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
Ignition switch is not in the ON position.
Diagnosis Procedure
INFOID:0000000010505355
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-169, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
BCS-135, "Removal and Installation"
.
Is the result normal?
YES
>> INSPECTION END.
NO
>> GO TO 3
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
SEC-284
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
VEHICLE SECURITY SYSTEM CANNOT BE SET
KEY FOB
KEY FOB : Description
INFOID:0000000010338084
Armed phase is not activated when all doors are locked using keyfob.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
KEY FOB : Diagnosis Procedure
INFOID:0000000010338085
1.
CHECK REMOTE KEYLESS ENTRY SYSTEM
Lock/unlock door with keyfob. Refer to
DLK-391, "REMOTE KEYLESS ENTRY FUNCTION : System Descrip-
(With super lock) or
(With out super lock).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
DLK-448, "Diagnosis Procedure"
.
2.
CHECK HOOD SWITCH
Check hood switch. Refer to
SEC-274, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
REPLACE BCM
• Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000010338086
ARMED phase is not activated when door is locked using door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• SECURITY ALARM SET: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000010338087
1.
CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door lock and unlock switch. Refer to
or
Is the inspection result normal?
YES
>> GO TO 2.
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-285
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NO
>> Check power door lock system (door lock function). Refer to
DLK-443, "ALL DOOR : Diagnosis
(With super lock) or
DLK-581, "ALL DOOR : Diagnosis Procedure"
(Without super
lock).
2.
CHECK HOOD SWITCH
Check hood switch. Refer to
SEC-274, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or Replace hood switch.
3.
REPLACE BCM
• Replace BCM. Refer to
BCS-135, "Removal and Installation"
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
UNLOCK SENSOR
UNLOCK SENSOR : Description
INFOID:0000000010506179
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
UNLOCK SENSOR : Diagnosis Procedure
INFOID:0000000010506180
1.
CHECK POWER DOOR LOCK SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to
(Without super
lock).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system (door lock function). Refer to
DLK-447, "Diagnosis Procedure"
(With super lock) or
DLK-585, "Diagnosis Procedure"
(Without super lock).
2.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-274, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
SEC-286
< SYMPTOM DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000010338088
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000010505375
1.
CHECK SENSOR CANCEL SWITCH
Check sensor cancel switch.
Refer to
SEC-279, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace sensor cancel switch.
2.
PERFORM SELF-DIAGNOSIS OF SIREN CONTROL UNIT
Perform self-diagnosis of siren control unit.
Refer to
SEC-207, "Diagnosis Description"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-430, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the malfunctioning door switch. Refer to
DLK-195, "Removal and Installation"
4.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-274, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace hood switch.
5.
CHECK INTRUDER SENSOR
Check intruder sensor.
Refer to
SEC-277, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace intruder sensor.
6.
REPLACE SIREN CONTROL UNIT
1.
Replace siren control unit.
2.
Confirm the operation after replacement.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 7.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст