Nissan Qashqai J11. Manual — part 940
PB-142
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000010833573
Removal and Installation
INFOID:0000000010833574
REMOVAL
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Release the parking brake.
CAUTION:
If the brake cannot be released, release it manually. Refer to
3.
Turn the ignition switch OFF.
4.
Disconnect battery negative terminal. Refer to
5.
Remove rear tires.
6.
Disconnect parking brake actuator harness connector.
7.
Remove parking brake actuator harness mounting bolts.
8.
Remove parking brake actuator harness from the vehicle.
INSTALLATION
Install the reverse order of the removal.
Parking brake actuator harness RH
Parking brake actuator harness LH
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSFIA2487GB
PARKING BRAKE ACTUATOR
PB-143
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE ACTUATOR
Exploded View
INFOID:0000000010471527
Removal and Installation
INFOID:0000000010318199
REMOVAL
1.
Turn the power switch ON.
2.
Release the parking brake.
3.
Turn the power switch OFF.
4.
Disconnect 12V battery negative terminal. Refer to
PB-5, "Precautions for Removing Battery Terminal"
.
5.
Remove rear wheel. Refer to
WT-63, "Removal and Installation"
6.
Disconnect parking brake actuator harness connector.
7.
Remove parking brake actuator from vehicle.
CAUTION:
To prevent damage to the parts, never drop remove parts.
1.
Bolt
2.
Actuator
3.
Sliding pin bolt
4.
Cap
5.
Bleeder valve
6.
Cylinder body
7.
Piston
8.
Piston boot
9.
Sliding pin boot
10.
Bushing
11. Torque member
12.
Outer shim
13.
Outer pad
14. Inner pad
15.
Inner shim
: Apply rubber grease.
: Apply brake fluid.
Refer to
for symbols not described on the above.
E1FIA0155GB
PB-144
< REMOVAL AND INSTALLATION >
PARKING BRAKE ACTUATOR
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform parking brake actuator ASSEMBLY CHECK,when electric parking brake control unit is removed and
installed, or replaced. Refer to
.
• Perform parking brake actuator AX-SENSOR CALIBRATION, when electric parking brake control unit is
removed and installed, or replaced. Refer to
.
• Perform adjustment after installation. Refer to
Inspection
INFOID:0000000010318200
ADJUSTMENT AFTER INSTALLATION
1.
Pull the parking brake switch 2 times and check that the electric parking brake indicator in combination
meter turns ON.
2.
Turn the power switch OFF and wait 20 minutes.
3.
Turn the power switch ON.
CAUTION:
Never set the vehicle to READY.
4.
Check that the electric parking brake indicator lamp in combination meter turns ON.
5.
Push parking brake switch to release electric parking brake.
6.
Check that the electric parking brake indicator lamp in combination meter turns OFF.
PARKING BRAKE SWITCH
PB-145
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SWITCH
Removal and Installation
INFOID:0000000010833576
REMOVAL
1.
Remove the console finisher assembly. Refer to
.
2.
Remove parking brake switch.
INSTALLATION
Install in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст