Nissan Qashqai J11. Manual — part 2015
PG
FUSIBLE LINK INSPECTION
PG-153
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUSIBLE LINK INSPECTION
How To Check
INFOID:0000000010464101
A melted fusible link can be detected either by visual inspection or by feeling with finger tip. If its condition is
questionable, use circuit tester or test lamp.
CAUTION:
• If fusible link should melt, it is possible that critical circuit (power supply or large current carrying
circuit) is shorted. In such a case, carefully check and eliminate cause of malfunction.
• Never wrap outside of fusible link with vinyl tape. Important: Never let fusible link touch any other
wiring harness, vinyl or rubber parts.
:Fusible link
JMMIA1915ZZ
PG-154
< REMOVAL AND INSTALLATION >
BATTERY
REMOVAL AND INSTALLATION
BATTERY
Exploded View
INFOID:0000000010464105
JMMIA1768GB
Battery fix frame
Battery fix rod
Cover
Battery terminal with fusible link
Battery
Battery cover
PG
BATTERY
PG-155
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Removal and Installation
INFOID:0000000010464106
REMOVAL
CAUTION:
After the battery of a vehicle equipped with the Stop/Start System is replaced, the cumulative battery
discharge current value stored in IPDM E/R must be erased, using CONSULT. Refer to
(With Stop/Start System).
1.
Disconnect the battery cable from the negative terminal.
CAUTION:
To prevent damage to the parts, disconnect the battery cable from the negative terminal first.
2.
Remove cover of battery positive terminal.
3.
Disconnect the battery cable from the positive terminal.
4.
Remove battery fix frame mounting nuts and battery fix frame.
5.
Remove battery.
6.
Remove tray.
7.
Remove battery mounting bracket assembly mounting bolts, and then remove battery mounting bracket
assembly.
8.
Remove battery mounting bracket mounting bolts, and then remove battery mounting bracket. (if
equipped)
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
To install the battery, carefully read the following instructions.
• To prevent damage to the parts, connect the battery cable to the positive terminal first.
• After connecting battery cables, to securely supply battery voltage, ensure that they are tightly
clamped to battery terminals for good contact.
• To securely supply battery voltage, check battery terminal for poor connection caused by corrosion.
Reset electronic systems as necessary. Refer to
GI-63, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Required Procedure After Battery Disconnection"
Battery mounting bracket assembly
Radiator core support LH
Battery bracket
Battery tray
Battery current sensor
Battery mounting bracket
(if equipped)
Battery mounting bracket
(if equipped)
: N·m (kg-m, ft-lb)
: N·m (Kg-m, ft-lb)
PG-156
< REMOVAL AND INSTALLATION >
BATTERY TERMINAL WITH FUSIBLE LINK
BATTERY TERMINAL WITH FUSIBLE LINK
Exploded View
INFOID:0000000010464107
Removal and Installation
INFOID:0000000010464108
REMOVAL
1.
Disconnect the battery cable from the negative terminal. Refer to
.
CAUTION:
To prevent damage to the parts, disconnect the battery cable from the negative terminal first.
2.
Remove cover of battery positive terminal.
3.
Disconnect battery cable from the positive terminal. Refer to
.
4.
Remove harness mounting nut and battery terminal with fusible link mounting nut.
5.
Disconnect harness connector and remove battery terminal with fusible link.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
To prevent damage to the parts, connect the battery cable to the positive terminal first.
: Battery terminal with fusible link
: Harness connector
: Vehicle front
: N·m (kg-m, ft-lb)
JMMIA1770GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст