Nissan Qashqai J11. Manual — part 142
LU-28
< REMOVAL AND INSTALLATION >
[MR20DD]
OIL COOLER
• Tighten the connector bolt
after aligning the stopper
on the oil
pan (upper) side with protrusion of oil cooler
.
Inspection
INFOID:0000000010624161
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
and
2.
Start the engine, and check that there is no leakage of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
: Engine front
JPBIA6907ZZ
OIL PUMP
LU-29
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
UNIT DISASSEMBLY AND ASSEMBLY
OIL PUMP
Exploded View
INFOID:0000000010624162
Oil pump is integrated in the oil pan (upper). Refer to
.
LU-30
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR20DD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000010624163
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(lmp qt)
Engine Oil Pressure
INFOID:0000000010624164
Unit: kPa (bar, kg/cm
2
, psi)
*: Engine oil temperature at 80
°
C (176
°
F)
Drain and refill
With oil filter change
3.8 (3-3/8)
Without oil filter change
3.6 (3-1/8)
Dry engine (Overhaul)
4.4 (3-7/8)
Engine speed
Approximate discharge pressure*
Idle speed
More than 85 (0.85, 0.867, 12.3)
2,000 rpm
More than 200 (2.0, 2.04, 29)
PRECAUTIONS
LU-31
< PRECAUTION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Liquid Gasket
INFOID:0000000010284204
REMOVAL OF LIQUID GASKET
• After removing the mounting bolts and nuts, separate the mating
surface using a seal cutter and remove the liquid gasket.
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to
lightly tap the gasket applied area.
CAUTION:
If for some unavoidable reason a tool such as a flat-bladed
screwdriver is used, be careful not to damage the mating sur-
faces.
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the
gasket application surface and the mating surface.
• Remove the liquid gasket completely from the groove of the
gasket application surface, mounting bolts and bolt holes.
2.
Wipe the gasket application surface and the mating surface with
white gasoline (lighting and heating use) to remove adhering
moisture, grease and foreign materials.
3.
Attach the liquid gasket to the tube presser.
Use Genuine Liquid Gasket or equivalent.
4.
Apply the gasket without breaks to the specified location with the
specified dimensions.
• If there is a groove for the liquid gasket application, apply the
gasket to the groove.
• As for the bolt holes, normally apply the gasket inside the
holes. If specified, it should be applied outside the holes. Make
sure to read the instruction in this manual.
• Within five minutes of gasket application, install the mating
component.
• If the liquid gasket protrudes, wipe it off immediately.
• Do not retighten after the installation.
• After 30 minutes or more have passed from the installation, fill
the engine oil and coolant.
CAUTION:
If there are instructions in this manual, observe them.
PBIC0275E
PBIC0003E
EMA0622D
SEM159F
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст