Nissan Qashqai J11. Manual — part 2281
CHASSIS MAINTENANCE
MA-159
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Check pad thickness from an inspection hole on cylinder body.
Check using a scale if necessary.
FRONT DISC BRAKE (LHD) : Inspection
INFOID:0000000011497396
APPEARANCE
Check surface of disc rotor for uneven wear, cracks, and serious damage. Replace if there are.
RUNOUT
1.
Fix the disc rotor to the wheel hub and bearing assembly with
wheel nuts (2 points at least).
2.
Inspect the runout with a dial gauge. [Measured at 10 mm (0.39
in) inside the disc edge.]
NOTE:
Check the wheel bearing axial end play before the inspection.
Refer to
(4WD).
3.
Find the installation position with a minimum runout by shifting the disc rotor-to-wheel hub and bearing
assembly installation position by one hole at a time if the runout exceeds the limit value.
4.
Replace or lathe the disc rotor if the runout exceeds the limit even after the above operation.
THICKNESS
Check the thickness of the disc rotor using a micrometer. Replace
the disc rotor if the thickness is below the wear limit.
REAR DISC BRAKE (LHD)
REAR DISC BRAKE (LHD) : Inspection
INFOID:0000000011497397
PAD WEAR
Standard thickness
: Refer to
DISC BRAKE (LHD) : In-
spection"
.
Wear limit thickness
: Refer to
DISC BRAKE (LHD) : In-
spection"
.
BRA0010D
Runout limit
: Refer to
DISC BRAKE (LHD) : In-
spection"
.
SBR019B
Wear limit thickness
: Refer to
DISC BRAKE (LHD) : In-
spection"
.
SBR020B
MA-160
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
Check pad thickness from an inspection hole on cylinder body.
Check using a scale if necessary.
REAR DISC BRAKE (LHD) : Inspection
INFOID:0000000011497398
APPEARANCE
Check surface of disc rotor for uneven wear, cracks, and serious damage. Replace if there are.
RUNOUT
1.
Fix the disc rotor to the wheel hub and bearing assembly with
wheel nuts (2 points at least).
2.
Inspect the runout with a dial gauge. [Measured at 10 mm (0.39
in) inside disc edge.]
NOTE:
Check the wheel bearing axial end play before the inspection.
Refer to
(4WD).
3.
Find the installation position with a minimum runout by shifting the disc rotor-to-wheel hub and bearing
assembly installation position by one hole at a time if the runout exceeds the limit value.
4.
Replace or lathe the disc rotor if the runout exceeds the limit even after the above operation.
THICKNESS
Check the thickness of the disc rotor using a micrometer. Replace
the disc rotor if the thickness is below the wear limit.
FRONT DISC BRAKE (RHD)
FRONT DISC BRAKE (RHD) : Inspection
INFOID:0000000011497399
PAD WEAR
Standard thickness
: Refer to
.
Wear limit thickness
: Refer to
.
BRA0010D
Runout limit
: Refer to
.
BRA0697D
Wear limit thickness
: Refer to
.
SFIA2284E
CHASSIS MAINTENANCE
MA-161
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Check pad thickness from an inspection hole on cylinder body.
Check using a scale if necessary.
FRONT DISC BRAKE (RHD) : Inspection
INFOID:0000000011497403
APPEARANCE
Check surface of disc rotor for uneven wear, cracks, and serious damage. Replace if there are.
RUNOUT
1.
Fix the disc rotor to the wheel hub and bearing assembly with
wheel nuts (2 points at least).
2.
Inspect the runout with a dial gauge. [Measured at 10 mm (0.39
in) inside the disc edge.]
NOTE:
Check the wheel bearing axial end play before the inspection.
Refer to
(4WD).
3.
Find the installation position with a minimum runout by shifting the disc rotor-to-wheel hub and bearing
assembly installation position by one hole at a time if the runout exceeds the limit value.
4.
Replace or lathe the disc rotor if the runout exceeds the limit even after the above operation.
THICKNESS
Check the thickness of the disc rotor using a micrometer. Replace
the disc rotor if the thickness is below the wear limit.
REAR DISC BRAKE (RHD)
REAR DISC BRAKE (RHD) : Inspection
INFOID:0000000011497406
PAD WEAR
Standard thickness
: Refer to
.
Wear limit thickness
: Refer to
.
BRA0010D
Runout limit
: Refer to
.
SBR019B
Wear limit thickness
: Refer to
.
SBR020B
MA-162
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
Check pad thickness from an inspection hole on cylinder body.
Check using a scale if necessary.
REAR DISC BRAKE (RHD) : Inspection
INFOID:0000000011497407
APPEARANCE
Check surface of disc rotor for uneven wear, cracks, and serious damage. Replace if there are.
RUNOUT
1.
Fix the disc rotor to the wheel hub and bearing assembly with
wheel nuts (2 points at least).
2.
Inspect the runout with a dial gauge. [Measured at 10 mm (0.39
in) inside disc edge.]
NOTE:
Check the wheel bearing axial end play before the inspection.
Refer to
(4WD).
3.
Find the installation position with a minimum runout by shifting the disc rotor-to-wheel hub and bearing
assembly installation position by one hole at a time if the runout exceeds the limit value.
4.
Replace or lathe the disc rotor if the runout exceeds the limit even after the above operation.
THICKNESS
Check the thickness of the disc rotor using a micrometer. Replace
the disc rotor if the thickness is below the wear limit.
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE : Inspection
INFOID:0000000010355434
STEERING GEAR
Standard thickness
: Refer to
.
Wear limit thickness
: Refer to
.
BRA0010D
Runout limit
: Refer to
.
BRA0697D
Wear limit thickness
: Refer to
.
SFIA2284E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст