Nissan Qashqai J11. Manual — part 1055
HA-46
< REMOVAL AND INSTALLATION >
[TYPE 1]
A/C UNIT ASSEMBLY
3.
Remove fixing screws (A), and then remove heater pipe cover.
4.
Remove heater pipe packing.
5.
Disengage fixing pawl, and then remove heater pipe clamp.
6.
Remove heater core from A/C unit assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
Refer to
when filling radiator with engine coolant.
EXPANSION VALVE
EXPANSION VALVE : Removal and Installation
INFOID:0000000010451999
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
23, "Perform Lubricant Return Operation"
REMOVAL
1.
Use a refrigerant collecting equipment (for HFO-1234yf) to discharge the refrigerant. Refer to
.
2.
Disengage fixing clip, and then remove insulator upper side.
3.
Remove mounting bolt, and then disconnect internal heat exchanger pipe from expansion valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve with suitable material such as vinyl
tape to avoid the entry of air.
4.
Remove mounting bolts, and then remove expansion valve.
JMIIA3386ZZ
: Pawl
JMIIA3387ZZ
JMIIA3388ZZ
A/C UNIT ASSEMBLY
HA-47
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CAUTION:
Cap or wrap the joint of the evaporator and expansion valve with suitable material such as vinyl
tape to avoid the entry of air.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant. Refer to
HA-48
< SERVICE DATA AND SPECIFICATIONS (SDS)
[TYPE 1]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Compressor
INFOID:0000000010452002
Lubricant
INFOID:0000000010452003
Refrigerant
INFOID:0000000010452004
Engine Idling Speed
INFOID:0000000010452005
.
Belt Tension
INFOID:0000000010452006
Model
Denso make
6SBH14
Type
Swash plate
Displacement
cm
3
(cu in)/rev
Maximum
140 (8.6)
Direction of rotation
Clockwise (viewed from clutch)
Drive belt
Poly V
Disc to pulley clearance
mm (in)
Standard
0.21 – 0.55 (0.008 – 0.022)
Name
ND-OIL12
Capacity
m
(Imp fl oz)
Total in system
110 (3.9)
Compressor (service part) charging
amount
110 (3.9)
Type
HFO-1234yf (R-1234yf)
Capacity
kg (lb)
0.5 (1.1)
APPLICATION NOTICE
HA-49
< HOW TO USE THIS MANUAL >
[TYPE 2]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
HOW TO USE THIS MANUAL
APPLICATION NOTICE
Information
INFOID:0000000010709188
Check the vehicle type to use the service information in this section.
Service information
Destination
Type 1
For Europe
HRA2DDT engine models
Type 2
For Europe
• K9K engine models
• R9M engine models
Type 3
Except for Europe
• HRA2DDT engine models
• MR20DD engine models
Type 4
Except for Europe
• K9K engine models
• R9M engine models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст