Nissan Qashqai J11. Manual — part 1188
REAR SEAT
SE-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000010478170
DISASSEMBLY
1.
Remove armrest.
• Unclip cup holder.
: Pawl
• Remove spring clip. Using suitable tool.
• Push armest towards the left side of the vehicle to disengage LH pivot pin from bracket.
• Twist and disengage RH hinge pin to remove armest.
2.
Using a suitable tool remove seat belt finisher.
: Pawl
3.
Sqeeze clips and push up to remove.
CAUTION:
Wear protective gloves and sleeves to prevent injury from
sharp edges on frame.
4.
Remove seat lock knob finisher.
• Remove seat lock knob.
- Remove the mating (1) by the rotation of the rod holder (2).
- Remove rod holder (2) from seat lock knob (1).
- Remove seat lock knob finisher.
: Pawl
5.
6.
Remove in one piece seatback pad and trim.
JMJIA9700ZZ
PIIB4084J
JMJIA9704ZZ
SE-36
< REMOVAL AND INSTALLATION >
REAR SEAT
7.
Remove hog ring to separate seatback pad and trim.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat-
back trim and seatback pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seatback trim
is assembled.
• Smooth out all wrinkles during assembly.
SEAT CUSHION
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000010478171
DISASSEMBLY
1.
Remove seat cushion. Refer to
SE-34, "Removal and Installation"
.
2.
Remove hog rings on the bottom side of seat cushion.
3.
Remove hog rings on the top side of seat cushion and separate the seat cushion trim from the seat cush-
ion pad.
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seat cushion
trim is assembled.
• Smooth out all wrinkles during assembly.
PIIB3356J
PIIB3356J
POWER SEAT SWITCH
SE-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
POWER SEAT SWITCH
Removal and Installation
INFOID:0000000010436343
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the front seat. Refer to
SE-28, "Removal and Installation"
2.
Remove the seat cushion outer finisher inside.
3.
Disconnect power seat switch connector.
4.
Remove power seat switch mounting screws
.
5.
Remove harness clip and remove power seat switch
from
seat cushion outer finisher.
INSTALLATION
Install in the reverse order of removal.
JMJIA9931ZZ
SE-38
< REMOVAL AND INSTALLATION >
HEATED SEAT SWITCH
HEATED SEAT SWITCH
Removal and Installation
INFOID:0000000010436338
REMOVAL
1.
Remove the console switch panel. Refer to
2.
Remove the mounting screws
, and then remove heat seat
switch and switch bracket
.
3.
Remove heated seat switch
from switch bracket.
INSTALLATION
Installation is in the reverse order of removal.
JMJIA9647ZZ
: Pawl
JMJIA9648ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст