Nissan Qashqai J11. Manual — part 803
DLN-128
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY30A]
LOCK INDICATOR LAMP
LOCK INDICATOR LAMP
Description
INFOID:0000000010288304
The following is the indications of indicator lamp after engine start.
AWDAWD INDICATOR LAMP AND LOCK INDICATOR LAMP
Diagnosis Procedure
INFOID:0000000010288305
1.
CHECK AWD WARNING LAMP
Start engine and drive at 30 km/h (19 MPH) or more for approx. 1 minute.
Does AWD warning lamp turn ON?
YES
>> Go to
DLN-126, "Diagnosis Procedure"
.
NO
>> GO TO 2.
2.
CHECK AWD MODE SWITCH
Perform the trouble diagnosis for AWD mode switch. Refer to
DLN-116, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK LOCK INDICATOR LAMP SIGNAL
With CONSULT
1.
Start the engine.
CAUTION:
Stop the vehicle.
2.
Change AWD mode switch in “LOCK” from “AUTO”.
3.
Check “AWD MODE MON” of AWD control unit CONSULT “DATA MONITOR”.
Does the item on “DATA MONITOR” indicate “LOCK”?
YES
>> GO TO 4.
NO
>> Replace AWD control unit. Refer to
DLN-124, "Diagnosis Procedure"
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the malfunctioning part.
Condition
AWD indicator lamp
LOCK indicator lamp
2WD mode
OFF
OFF
AUTO mode
ON
OFF
LOCK mode
ON
ON
AWD CONTROL UNIT
DLN-129
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ECU DIAGNOSIS INFORMATION
AWD CONTROL UNIT
Reference Value
INFOID:0000000010288306
VALUES ON THE DIAGNOSIS TOOL
Monitor item
Condition
Value/Status
FR RH SENSOR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
Approximately equal to the indi-
cation on speedometer (Inside
of
±
10%)
FR LH SENSOR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
Approximately equal to the indi-
cation on speedometer (Inside
of
±
10%)
RR RH SENSOR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
Approximately equal to the indi-
cation on speedometer (Inside
of
±
10%)
RR LH SENSOR
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under standard condition.
Approximately equal to the indi-
cation on speedometer (Inside
of
±
10%)
BATTERY VOLT
Always
Battery voltage
THRTL POS SEN
When depressing accelerator pedal
(Value rises gradually in response to throttle position.)
0 – 100%
ETS SOLENOID
Engine running
• At idle speed
AWDAWD mode switch: 2WD
Approx. 0.000 A
AWD indicator lamp: ON
Approx. 0.000 A
LOCK indicator lamp: ON
Approx. 0.000 A
Engine running
• When depressing accelerator
pedal
AWD mode switch: 2WD
Approx. 0.000 A
AWD indicator lamp: ON
R9M: Approx. 0.000 – 2.000 A*
LOCK indicator lamp: ON
R9M: Approx. 2.000 A
STOP LAMP SW
Brake pedal: Depressed
On
Brake pedal: Released
Off
ENG SPEED SIG
Engine stopped
(Engine speed: Less than 400 rpm)
Stop
Engine running
(Engine speed: 400 rpm or more)
Run
ETS ACTUATOR
Engine stopped (Ignition switch: ON)
Off
Engine running
On
4WD WARN LAMP
AWD warning lamp: ON
On
AWD warning lamp: OFF
Off
4WD MODE SW
AWD mode switch: 2WD
2WD
AWD mode switch: AUTO
AUTO
AWD mode switch: LOCK
(State of hold of LOCK position)
LOCK
DLN-130
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY30A]
AWD CONTROL UNIT
*: The values are changed by throttle opening and engine speed.
TERMINAL LAYOUT
PHYSICAL VALUES
4WD MODE SW
AWD mode switch: 2WD
2WD
AWD mode switch: AUTO
AUTO
AWD mode switch: AUTO
⇒
LOCK
(State of AWD indicator lamp turn ON)
AUTO
⇒
LOCK
AWD mode switch: AUTO
⇒
LOCK
(State of LOCK indicator lamp turn ON)
LOCK
⇒
AUTO
DIS-TIRE MONI
Vehicle running with normal size tire installed
0 – 4 mm
Vehicle running with improper size tire installed (Front/rear tire
size difference, wear condition)
4 – 8 mm, 8 – mm
PARKING BRAKE SW SIG
Parking brake operated
On
Parking brake not operated
Off
Monitor item
Condition
Value/Status
JSDIA0057ZZ
Terminal No.
(Wire color)
Description
Condition
Value (Approx.)
+
-
Signal name
Input/
Output
1
(LG)
Ground
AWD solenoid power sup-
ply
Output
Engine speed: At idle
AWD mode switch: 2WD
0 V
AWD indicator lamp: ON
0 V
LOCK indicator lamp: ON
0 V
Engine speed: 3,000
rpm or more constant
AWD mode switch: 2WD
0 V
AWD indicator lamp: ON
2.5 V*
LOCK indicator lamp: ON
8 V
2
(L)
Ground
AWD solenoid ground
—
Engine speed: At idle
0 V
Engine speed: 3,000 rpm or more constant
0 V
5
(V)
Ground
AWD mode switch (AUTO)
Output
Ignition switch: ON
AWD mode switch: 2WD
Battery voltage
AWD mode switch: AUTO
0 V
AWD mode switch: LOCK
(State of hold of LOCK position)
0 V
7
(P)
Ground
Ignition switch
Input
Ignition switch: ON
Battery voltage
Ignition switch: OFF
0 V
8
(L)
—
CAN-H
Input/
Output
—
—
9
(G)
Ground
Power supply (AWD sole-
noid)
Input
Ignition switch: ON
Battery voltage
Ignition switch: OFF
Battery voltage
AWD CONTROL UNIT
DLN-131
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
*: The values are changed by throttle opening and engine speed.
CAUTION:
When using circuit tester to measure voltage for inspection, be sure not to extend forcibly any connector terminals.
Wiring Diagram - AWD SYSTEM -
INFOID:0000000010288307
FOR RUSSIA
10
(B)
Ground
Ground
—
Always
0 V
11
(B)
Ground
Ground
—
Always
0 V
12
(BR)
Ground
AWD mode switch (2WD)
Output
Ignition switch: ON
AWD mode switch: 2WD
0 V
AWD mode switch: AUTO
Battery voltage
AWD mode switch: LOCK
(State of hold of LOCK position)
Battery voltage
14
(Y)
Ground
AWD mode switch (LOCK)
Output
Ignition switch: ON
AWD mode switch: 2WD
Battery voltage
AWD mode switch: AUTO
Battery voltage
AWD mode switch: LOCK
(State of hold of LOCK position)
0 V
16
(P)
—
CAN-L
Input/
Output
—
—
Terminal No.
(Wire color)
Description
Condition
Value (Approx.)
+
-
Signal name
Input/
Output
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст