Nissan Qashqai J11. Manual — part 974
THE BRAKING DISTANCE IS LONG
BRC-133
< SYMPTOM DIAGNOSIS >
[WITH ESP]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
THE BRAKING DISTANCE IS LONG
Description
INFOID:0000000010329880
Brake stopping distance is long when ABS function is operated.
Diagnosis Procedure
INFOID:0000000010329881
CAUTION:
Brake stopping distance on slippery road like rough road, gravel road or snowy road may become
longer when ABS is operated than when ABS is not operated.
1.
CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check each components of brake system.
2.
CHECK BRAKE PERFORMANCE
Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check brake
stopping distance in this condition. Connect harness connectors after checking.
Is the inspection result normal?
YES
>> Normal
NO
>> Check each components of brake system.
BRC-134
< SYMPTOM DIAGNOSIS >
[WITH ESP]
DOES NOT OPERATE
DOES NOT OPERATE
Description
INFOID:0000000010329882
VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function, Brake
assist function, hill start assist function or Brake force distribution function does not operate.
Diagnosis Procedure
INFOID:0000000010329883
CAUTION:
• VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) func-
tion, Brake assist function, hill start assist function and Brake force distribution function never oper-
ate when the vehicle speed is 10 km/h (6.2 MPH) or less. However, TCS function, Brake limited slip
differential (BLSD) function and hill start assist function operates when the vehicle speed is 0 km/h
(0 MPH) (the vehicle is in stop status).
• VDC function and TCS function never operate when VDC OFF switch is operated (when VDC OFF
indicator lamp turns ON).
1.
CHECK ABS WARNING LAMP
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn ON and turn OFF approx. 1
second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and VDC warning
lamp and stay in OFF status during driving.
CAUTION:
Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?
YES
>> Normal
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Turn the ignition switch OFF
→
ON.
CAUTION:
• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
• Start the engine.
2.
Repeat step 1 two or more times.
3.
Perform self-diagnosis for “ABS” with CONSULT.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> Inspection End.
BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS
BRC-135
< SYMPTOM DIAGNOSIS >
[WITH ESP]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS
Description
INFOID:0000000010329884
• Brake pedal vibrates and motor sound from ABS actuator and electric unit (control unit) occurs, when the
engine starts.
• Brake pedal vibrates during braking.
CAUTION:
Vibration may be felt during brake pedal is lightly depressed (just placing a foot on it) in the following
conditions. This is normal.
• When shifting gears
• When driving on slippery road
• During cornering at high speed
• When passing over bumps or grooves [Approx. 50 mm (1.97 in) or more]
• When pulling away just after starting engine [at approx. 10 km/h (6.2 MPH) or higher]
Diagnosis Procedure
INFOID:0000000010329885
1.
SYMPTOM CHECK 1
Check that there are pedal vibrations when the engine is started.
Do vibrations occur?
YES
>> GO TO 2.
NO
>> Check brake pedal. Refer to
BR-8, "Inspection and Adjustment"
2.
SYMPTOM CHECK 2
Check that motor sound from ABS actuator occurs when the engine starts.
Does the operation sound occur?
YES
>> GO TO 3.
NO
>> Perform self-diagnosis for “ABS” with CONSULT.
3.
SYMPTOM CHECK 3
Check symptoms when electrical component (headlamps, etc.) switches are operated.
Does the symptom occur?
YES
>> Check that radio (including wiring), antenna and antenna lead-in wires are not located near ABS
actuator and electric unit (control unit). Move them if they are located near ABS actuator and elec-
tric unit (control unit).
NO
>> GO TO 4.
4.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Turn the ignition switch OFF
→
ON.
CAUTION:
• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
• Start the engine.
2.
Repeat step 1 two or more times.
3.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> Inspection End.
BRC-136
< SYMPTOM DIAGNOSIS >
[WITH ESP]
VEHICLE JERKS DURING
VEHICLE JERKS DURING
Description
INFOID:0000000010329886
The vehicle jerks when VDC function, TCS function, ABS function, EBD function, Brake limited slip differential
(BLSD) function, Brake assist function, hill start assist function or Brake force distribution function operates.
Diagnosis Procedure
INFOID:0000000010329887
1.
CHECK SYMPTOM
Check that the vehicle jerks when VDC function, TCS function, ABS function, EBD function, Brake limited slip
differential (BLSD) function, Brake assist function, hill start assist function or Brake force distribution function
operates.
Is the inspection result normal?
YES
>> Normal
NO
>> GO TO 2.
2.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Turn the ignition switch OFF
→
ON.
CAUTION:
• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
• Start the engine.
2.
Repeat step 1 two or more times.
3.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK CONNECTOR
With CONSULT
1.
Turn the ignition switch OFF.
2.
Disconnect ABS actuator and electric unit (control unit) harness connector.
3.
Check connector terminal for deformation, disconnection and looseness.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Poor connection of connector terminal. Repair or replace connector terminal.
4.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Connect harness connector.
2.
Turn the ignition switch OFF
→
ON.
CAUTION:
• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
• Start the engine.
3.
Repeat step 2 two or more times.
4.
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 5.
5.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”, “TRANSMISSION”.
Is any DTC detected?
YES
>> Check the DTC.
NO
>> Replace ABS actuator and electric unit (control unit). Refer to
BRC-142, "Removal and Installa-
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст