Nissan Qashqai J11. Manual — part 1292
SUPER LOCK ACTUATOR
DLK-437
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010502785
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-437, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010502786
1.
CHECK SUPER LOCK ACTUATOR SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (passenger side) connector.
3.
Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM and each door lock assembly.
2.
Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
3.
Check continuity between BCM connector and ground.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
148
Ground
Super lock
Release
9 – 16 V
149
Set
(+)
(–)
Condition
Voltage
Front door lock assembly (passenger side)
Connector
Terminal
D2
1
Ground
Super lock
Set
9 – 16 V
2
Release
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M68
139
D2
2
Existed
149
1
BCM
Ground
Continuity
Connector
Terminal
M68
139
Not existed
149
DLK-438
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 3]
SUPER LOCK ACTUATOR
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR LH
REAR LH : Component Function Check
INFOID:0000000010502787
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-438, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000010502788
1.
CHECK SUPER LOCK ACTUATOR OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly LH.
3.
Check voltage between rear door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM, each door lock actuator and fuel filler lid lock actuator connector.
2.
Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3.
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M68
139
Ground
Super lock
Release
9 – 16 V
149
Set
(+)
(–)
Condition
Voltage
Rear door lock assembly LH
Connector
Terminal
D52
1
Ground
Super lock
Set
9 – 16 V
2
Release
BCM
Rear door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D52
2
Existed
131
1
SUPER LOCK ACTUATOR
DLK-439
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
REAR RH
REAR RH : Component Function Check
INFOID:0000000010502789
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Touch “LOCK” or “UNLOCK” to check that it works normally.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-439, "REAR RH : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000010502790
1.
CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH.
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM, each door lock actuator and fuel filler lid lock actuator connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not existed
131
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Super lock
Release
9 – 16 V
131
Set
(+)
(–)
Condition
Voltage
Rear door lock assembly RH
Connector
Terminal
D65
1
Ground
Super lock
Set
9 – 16 V
2
Release
DLK-440
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 3]
SUPER LOCK ACTUATOR
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each door lock actuator.
NO
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
BCM
Rear door lock assembly RH
Continuity
Connector
Terminal
Connector
Terminal
B3
124
D65
2
Existed
131
1
BCM
Ground
Continuity
Connector
Terminal
B3
124
Not Existed
131
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
B3
124
Ground
Super lock
Release
9 – 16 V
131
Set
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст