Nissan Qashqai J11. Manual — part 253
ECH-310
< SYMPTOM DIAGNOSIS >
[HRA2DDT]
STOP/START SYSTEM NOT ACTIVATED
Is the indication less than 65,000?
YES
>> GO TO 7.
NO
>> Replace battery designed for the stop/start system. Refer to
PG-155, "Removal and Installation"
7.
CHARGE BATTERY
Charge battery. Refer to
PG-136, "FOR MAINTENANCE REQUIRED BATTERY MODELS : How to Handle
(for maintenance required battery models) or
PG-142, "FOR MAINTENANCE FREE BATTERY MOD-
(for maintenance free battery models).
>> GO TO 8.
8.
CHECK BATTERY STATUS
WITH CONSULT
1.
Start the engine and warm up the engine coolant temperature to 45
°
C (113
°
F) or more.
2.
Check the temperature of battery fluid is 0
°
C (32
°
F) or more.
3.
Select “BATTERY STATUS” in “DATA MONITOR” mode of “IPDM E/R” using CONSULT.
4.
Check the “BATTERY STATUS” indication.
Is “OK” displayed on CONSULT screen?
YES
>> GO TO 9.
NO
>> Check battery. Refer to
PG-136, "FOR MAINTENANCE REQUIRED BATTERY MODELS : How
(maintenance required battery) or
PG-142, "FOR MAINTENANCE FREE BAT-
TERY MODELS : How to Handle Battery"
(maintenance free battery).
9.
CHECK STOP/START OFF SWITCH
Check the stop/start OFF switch. Refer to
ECH-300, "Component Function Check"
.
Is the inspection normal?
YES
>> GO TO 10.
NO
>> Repair or replace error-detected parts.
10.
CHECK HOOD SWITCH
Check the hood switch. Refer to
ECH-298, "Component Function Check"
.
Is the inspection normal?
YES
>> GO TO 11.
NO
>> Repair or replace error-detected parts.
11.
CHECK STOP/START SYSTEM OPERATION CONDITION
Check the stop/start system operation condition. Refer to
ECH-33, "STOP/START SYSTEM : System Descrip-
.
>> INSPECTION END
Monitor item
Indication
BAT DISCHAGE COUNT
Less than 65,000
EVAPORATIVE EMISSION SYSTEM
ECH-311
< PERIODIC MAINTENANCE >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
ECH
N
P
O
PERIODIC MAINTENANCE
EVAPORATIVE EMISSION SYSTEM
Inspection
INFOID:0000000010379191
1.
Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration.
2.
Check EVAP canister as follows:
a.
Block port (A). Orally blow air through port (B).
Check that air flows freely through port (C).
b.
Block port (B). Orally blow air through port (A).
Check that air flows freely through port (C).
3.
Inspect fuel tank filler cap vacuum relief valve for clogging, stick-
ing, etc.
a.
Wipe clean valve housing.
b.
Check valve opening pressure and vacuum.
c.
If out of specification, replace fuel filler cap as an assembly.
Refer to
JSBIA0335ZZ
SEF989X
Pressure:
15.3 - 20.0 kPa (0.153 - 0.200 bar, 0.156 - 0.204 kg/
cm
2
, 2.22 - 2.90 psi)
Vacuum:
–6.0 to –3.4 kPa (–0.06 bar to –-0.034bar, –0.061 to –
0.035 kg/cm
2
, –0.87 to –0.49 psi)
SEF943S
ECH-312
< REMOVAL AND INSTALLATION >
[HRA2DDT]
VACUUM LINES
REMOVAL AND INSTALLATION
VACUUM LINES
Vacuum Layout
INFOID:0000000010501191
CAUTION:
Do not use soapy water or any type of solvent while installing vacuum hose.
1.
Intake manifold
2.
Engine coolant bypass valve control
solenoid valve
3.
Engine coolant bypass valve control
actuator
4.
TC wastegate control actuator
5.
Turbocharger
6.
TC wastegate control solenoid valve
JSBIA4856ZZ
ECM
ECH-313
< REMOVAL AND INSTALLATION >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
ECH
N
P
O
ECM
Exploded View
INFOID:0000000010501192
Removal and Installation
INFOID:0000000010501193
CAUTION:
Perform ADDITIONAL SERVICE WHEN REPLACING ECM. Refer to
REMOVAL
1.
Disconnect battery negative terminal.
2.
Remove air duct (inlet). Refer to
EM-23, "Removal and Installation"
3.
Disconnect ECM harness connectors.
4.
Remove battery, battery cover and battery tray. Refer to
PG-155, "Removal and Installation"
.
5.
Remove bracket A with ECM.
6.
Remove ECM from bracket B.
INSTALLATION
Install in the reverse order of removal.
1.
Battery mounting bracket
2.
Bracket A
3.
Bracket B
4.
ECM
: N·m (kg-m, in-lb)
JSBIA5191GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст