Nissan Qashqai J11. Manual — part 1598
BRM-220
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
BODY ALIGNMENT
2WD : Rear Body
INFOID:0000000010498844
MEASUREMENT
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
«The others»
Unit: mm (in)
MEASUREMENT POINTS
Outer side body indent
Rear seat crossmember hole center
:
φ
16 (0.63)
: 18
×
16 (0.71
×
0.63)
Front pillar indent
Door hinge installing hole center
:
φ
12 (0.47)
:
φ
9 (0.35)
Point
Material
Point
Material
Unit: mm (in)
JSKIA3915GB
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
–
987 (38.86)*
–
688 (27.09)*
–
578 (22.76)*
BODY ALIGNMENT
BRM-221
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Unit: mm (in)
4WD
4WD : Body Center Marks (Without Sunroof Models)
INFOID:0000000010499774
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
: Vehicle front
JSKIA3916ZZ
Point
Material
Point
Material
Roof flange end of center positioning mark
Lower rear pillar reinforcement joggle
Rear fender extension joggle
Back door lock support hole center
φ
14 (0.55)
Lower back pillar main joggle
BRM-222
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
BODY ALIGNMENT
Unit: mm (in)
4WD : Body Center Marks (With Sunroof Models)
INFOID:0000000010499775
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
: Vehicle front
Points
Portion
Marks
A
Front roof
Embossment
B
Cowl top
indent
C
Cowl top
Hole
φ
8 (0.31)
D
Trans control reinforcement
Hole 12
×
14 (0.47
×
0.55)
E
Rear roof
Embossment
JSKIA3956ZZ
BODY ALIGNMENT
BRM-223
< SERVICE DATA AND SPECIFICATIONS (SDS)
[FOR EUROPE (RHD)]
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Unit: mm (in)
4WD : Description
INFOID:0000000010499776
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
• When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
• Measurements should be taken at the center of the mounting holes.
: Vehicle front
Points
Portion
Marks
A
Upper front roof rail
Embossment
B
Cowl top
indent
C
Cowl top
Hole
φ
8 (0.31)
D
Trans control reinforcement
Hole 12
×
14 (0.47
×
0.55)
E
Rear roof
Embossment
JSKIA3957ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст