Nissan Qashqai J11. Manual — part 596
STR-26
< REMOVAL AND INSTALLATION >
STARTER MOTOR
MR16DDT : Exploded View
INFOID:0000000011732944
REMOVAL
MR16DDT : Removal and Installation
INFOID:0000000011732945
REMOVAL
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-155, "Removal and Installation"
2.
Remove intake monifold. Refer to
EM-151, "Removal and Installation"
3.
Open “B” terminal cover, in the direction indicated by an arrow
as shown in the figure.
4.
Remove “B” terminal nut and “B” terminal harness.
5.
Remove “S” terminal nut and “S” terminal harness.
6.
Disconnect harness connector from oil level sensor and oil pressure contorl solenoid valve. Refer to
1.
“S” terminal harness
2.
“B” terminal harness
3.
Starter motor
4.
Cylinder block
: Vehicle front
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
PKIC8095E
JMBIA3020ZZ
STARTER MOTOR
STR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
7.
Disconnect harness connector (1) from crankshaft position sen-
sor.
8.
Remove harness fixing clip (A) from oil pan (upper), and then
move harness (2) to a location where they do not inhibit work.
9.
Remove starter motor mounting bolts.
10. Remove starter motor from the vehicle.
CAUTION:
For models with STOP/START SYSTEM, never erase the starter operation counter except when
replacing starter motor.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Be careful to tighten “B” terminal nut to the specified torque.
• Erase the starter operation counter when the starter motor for models with STOP/START SYSTEM is
replaced. Refer to
• Replace the engine restart bypass relay and the fuel pump relay when the starter motor models with
STOP/START SYSTEM is replaced.
- Engine restart bypass relay: Refer to
ECM-619, "Removal and Installation"
- Fuel pump relay (IPDM E/R): Refer to
PCS-68, "Removal and Installation"
.
MR20DD
MR20DD : Exploded View
INFOID:0000000010376819
REMOVAL
JMBIA3021ZZ
1.
“S” terminal connector
2.
Starter motor
3.
Cylinder block
: Vehicle front
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMBIA4561GB
STR-28
< REMOVAL AND INSTALLATION >
STARTER MOTOR
DISASSEMBLY
MR20DD : Removal and Installation
INFOID:0000000010376820
REMOVAL
1.
Disconnect the battery cable from the negative terminal. Refer to
.
2.
Disconnect the oil pressure switch connector.
3.
Remove “B” terminal nut and “B” terminal harness.
4.
Remove “S” terminal nut and “S” terminal harness.
5.
Remove starter motor mounting bolts.
6.
Remove starter motor upward from the vehicle.
CAUTION:
Never damage oil pressure switch when removing starter motor.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Be careful to tighten “B” terminal nut to the specified torque.
1.
Magnetic switch assembly
2.
Dust cover kit
3.
Shift lever set
4.
Center bracket (A)
5.
Yoke assembly
6.
Armature assembly
7.
Brush holder assembly
8.
Thrust washer
9.
Rear cover assembly
10. Internal gear
11.
Planetary gear
12. Pinion shaft
13. Packing
14. Thrust washer
15. Center bracket (P)
16. E-ring
17. Pinion assembly
18. Pinion stopper
19. Pinion stopper clip
20. Gear case assembly
: High-temperature grease point
: N·m (kg-m, in-lb)
JMBIA4574GB
STARTER MOTOR
STR-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
MR20DD : Disassembly and Assembly
INFOID:0000000010376821
ASSEMBLY
Apply high-temperature grease to lubricate the bearing, gears and frictional surface when assembling
the starter.
Carefully observe the following instructions.
Pinion Protrusion Length Adjustment
CLEARANCE
• With pinion driven out by magnetic switch, push pinion back to
remove slack and measure clearance “L” between the front edge
of the pinion and the pinion stopper.
• Adjust with the adjusting plate if the measurement value is not in
the specified area.
MR20DD : Inspection
INFOID:0000000010376822
INSPECTION
Magnetic Switch Check
• Before starting to check, disconnect the battery cable from the negative terminal.
• Disconnect “M” terminal of starter motor.
1.
Continuity test [between “S” terminal (A) and switch body]
• Replace magnetic switch if continuity does not exist.
Clearance “L”
: Refer to SDS
SKIB0229E
PKID0786E
B
: “B” terminal
C
: “M” terminal
SKIB9002E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст