Nissan Qashqai J11. Manual — part 740
P0715 INPUT SPEED SENSOR A
TM-535
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Connect all of disconnected connectors.
2.
Lift the vehicle.
3.
Start the engine.
4.
Check frequency of primary speed sensor.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace primary speed sensor. Refer to
TM-634, "Removal and Installation"
6.
DETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and primary speed sensor. Refer to
"Wiring Diagram - IGNITION POWER SUPPLY -"
.
• 10A fuse [No.74, located in fuse block (J/B)]. Refer to
PG-97, "Fuse, Connector and Terminal Arrangement"
.
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
+
−
Condition
Frequency
(Approx.)
TCM
Connector
Terminal
F1
35
Ground
• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)
700 Hz
JSDIA1905GB
TM-536
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0717 INPUT SPEED SENSOR A
P0717 INPUT SPEED SENSOR A
DTC Logic
INFOID:0000000010245611
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Start the engine.
2.
Drive the vehicle.
3.
Maintain the following conditions for 10 seconds or more.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P0717
INPUT SPEED SENSOR A
(Input/Turbine Speed Sensor
“A” Circuit No Signal)
When 1 is satisfied and any of 2, 3 or 4 is satisfied:
1.
When the following conditions are satisfied:
-
TCM power supply voltage: More than 11 V
-
After range change completion, it spends 2
seconds or more.
2.
When all of the following conditions are satis-
fied and this state is maintained for 5 sec-
onds:
-
Primary pulley speed: 500 rpm or more
-
Input speed: Less than 150 rpm
-
Range: Other than P, N
-
P0705, P0706, or P0715 is not detected.
3.
When all of the following conditions are satis-
fied and this state is maintained for 0.5 sec-
onds:
-
10-msec-ago input speed: 1,000 rpm or more
-
Now input speed: 0 rpm
4.
When all of the following conditions are satis-
fied and this state is maintained for 5 sec-
onds:
-
Range: D or Ds
-
Engine speed: 450 rpm or more
-
Input peed: 300 rpm or more
-
Primary pulley speed: 300 rpm or more
-
Secondary pulley seed: 300 rpm or more
-
Differences between engine speed and pri-
mary pulley speed: 1,000 rpm or less
-
Differences between primary pulley speed
and input speed: More than 1,000 rpm
-
Differences between engine speed and input
speed: More than 1,000 rpm
-
Lock-up command is being given (except for
slip lock-up)
-
DTC other than the applicable DTC is not de-
tected.
• Harness or connectors
(Input speed sensor circuit is open
or shorted.)
• Input speed sensor
Selector lever
: “D” position
P0717 INPUT SPEED SENSOR A
TM-537
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Stop the vehicle.
5.
Check the first trip DTC.
Is “P0717” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010245612
1.
CHECK INPUT SPEED SENSOR POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect input speed sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between input speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 6.
2.
CHECK INPUT SPEED SENSOR GROUND CIRCUIT
Check continuity between input speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between input speed sensor harness connector terminal and TCM harness connector
terminal.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK CIRCUIT BETWEEN INPUT SPEED SENSOR AND TCM (PART 2)
Check continuity between input speed sensor harness connector terminal and ground.
Engine speed
: 1,200 rpm or more
Vehicle speed
: 40 km/h (25 MPH) or more
+
−
Voltage
Input speed sensor
Connector
Terminal
F47
3
Ground
10 – 16 V
Input speed sensor
—
Continuity
Connector
Terminal
F47
1
Ground
Existed
Input speed sensor
TCM
Continuity
Connector
Terminal
Connector
Terminal
F47
2
F1
24
Existed
TM-538
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0717 INPUT SPEED SENSOR A
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK TCM INPUT SIGNALS
1.
Connect all of disconnected connectors.
2.
Lift the vehicle.
3.
Start the engine.
4.
Check frequency of input speed sensor.
Is the inspection result normal?
YES >> Check
intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace input speed sensor. Refer to
TM-632, "Removal and Installation"
6.
DETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and input speed sensor. Refer to
ing Diagram - IGNITION POWER SUPPLY -"
.
• 10A fuse [No.74, located in the fuse block (J/B]. Refer to
PG-97, "Fuse, Connector and Terminal Arrange-
.
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Input speed sensor
—
Continuity
Connector
Terminal
F47
2
Ground
Not existed
+
−
Condition
Frequency
(Approx.)
TCM
Connector
Terminal
F1
24
Ground
• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)
880 Hz
JSDIA3769GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст