Nissan Qashqai J11. Manual — part 1114
HAC-92
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
B24A9 SUNLOAD SENSOR
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair harness or connector.
6.
CHECK SUNLOAD SENSOR POWER SUPPLY CIRCUIT FOR SHORT
1.
Check continuity between sunload sensor harness connector and ground.
2.
Check voltage between in-vehicle harness connector and ground
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-129, "Removal and Installation"
.
NO
>> Repair harness or connector.
7.
CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-129, "Removal and Installation"
.
NO
>> Repair or replace malfunctioning parts.
Sunload sensor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M82
1
M141
54
Existed
Sunload sensor
—
Continuity
Connector
Terminal
M82
1
Ground
Not existed
+
−
Voltage
Sunload sensor
Connector
Terminal
M82
1
Ground
0 V
B24B4 A/C CONTROL
HAC-93
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
B24B4 A/C CONTROL
DTC Logic
INFOID:0000000010500503
DTC DETECTION LOGIC
POSSIBLE CAUSE
A/C control (Internal circuit malfunction)
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “HVAC” using CONSULT.
3.
Check DTC.
Is DTC detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010500504
1.
REPLACE A/C CONTROL
Replace A/C control. Refer to
HAC-128, "Removal and Installation"
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B24B4
A/C CONTROL
(Air conditioning control)
[GENERAL ELEC MALFUNCTN]
An internal circuit error message is received from A/C
control via LIN communication for 30 seconds or more.
HAC-94
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
B24B7 INTAKE DOOR MOTOR
B24B7 INTAKE DOOR MOTOR
DTC Logic
INFOID:0000000010432215
DTC DETECTION LOGIC
POSSIBLE CAUSE
[CIRCUIT SHORT TO BATTERY]
• Harness and connector (Intake door motor circuit is shorted to battery)
• Intake door motor
• A/C auto amp.
[CIRC SHORT TO GRND OR OPEN]
• Harness and connector (Intake door motor circuit is open or shorted to ground)
• Intake door motor
• A/C auto amp.
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “HVAC” using CONSULT.
3.
Check DTC.
Is DTC detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010432216
1.
CHECK INTAKE DOOR MOTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect intake door motor connector.
3.
Turn ignition switch ON.
4.
Check voltage between intake door motor harness connector and ground for several seconds after press-
ing the INTAKE switch.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK INTAKE DOOR MOTOR POWER SUPPLY CIRCUIT FOR OPEN
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B24B7
INTAKE DOOR MOTOR
(Intake door motor)
[CIRCUIT SHORT TO BATTERY]
Detect short to battery circuit of intake door motor cir-
cuits.
[CIRC SHORT TO GRND OR
OPEN]
Detect open or short to ground circuit of intake door
motor circuits.
+
−
Voltage
Intake door motor
Connector
Terminal
M341
2
Ground
11 - 14 V
B24B7 INTAKE DOOR MOTOR
HAC-95
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
1.
Turn ignition switch OFF.
2.
Disconnect A/C auto amp. connector.
3.
Check continuity between intake door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK INTAKE DOOR MOTOR POWER SUPPLY CIRCUIT FOR SHORT
Check continuity between intake door motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace A/C auto amp. Refer to
HAC-129, "Removal and Installation"
.
NO
>> Repair harness or connector.
4.
CHECK INTAKE DOOR MOTOR DRIVE SIGNAL CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect A/C auto amp. connector.
3.
Check continuity between intake door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK INTAKE DOOR MOTOR DRIVE SIGNAL CIRCUIT FOR SHORT
1.
Check continuity between intake door motor harness connector and ground.
2.
Check voltage between intake door motor harness connector and ground.
Intake door motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M341
2
M140
20
Existed
Intake door motor
—
Continuity
Connector
Terminal
M341
2
Ground
Not existed
Intake door motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M341
6
M140
14
Existed
1
16
3
17
4
36
Intake door motor
—
Continuity
Connector
Terminal
M341
6
Ground
Not existed
1
3
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст