Nissan Qashqai J11. Manual — part 1348
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-661
< SYSTEM DESCRIPTION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM (INTELLIGENT KEY SYSTEM)
INTELLIGENT KEY SYSTEM
INTELLIGENT KEY SYSTEM : System Diagram
INFOID:0000000010672304
INTELLIGENT KEY SYSTEM : System Description
INFOID:0000000010672305
• The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/
unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).
CAUTION:
The driver should always carry the Intelligent Key
• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be
registered.
• It is possible to perform a diagnosis on the system and register an Intelligent Key with CONSULT.
JMKIB3316GB
Function
Description
Refer
Door lock
Lock/unlock can be performed by pressing the request switch
Back door open
The back door can be opened by carrying the Intelligent Key and pressing the
back door opener switch.
Remote keyless entry
Lock/unlock can be performed by pressing the remote controller button of the In-
telligent Key
DLK-662
< SYSTEM DESCRIPTION >
[TYPE 5]
SYSTEM (INTELLIGENT KEY SYSTEM)
DOOR LOCK FUNCTION
DOOR LOCK FUNCTION : System Diagram
INFOID:0000000010672306
DOOR LOCK FUNCTION : System Description
INFOID:0000000010672307
When pressing the door request switch, it is possible to lock and unlock the door by carrying the Intelligent
Key.
OPERATION DESCRIPTION
• When the BCM detects that each door request switch is pressed, it starts the outside key antenna and inside
key antenna corresponding to the pressed door request switch and transmits the request signal to the Intelli-
gent Key. And then, check that the Intelligent Key is near the door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM lock/unlock each door lock actuator.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the door request switch is
operated.
Key reminder
The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle
Warning
If an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver
Engine start
The engine can be turned on while carrying the Intelligent Key
Interior room lamp control
Interior room lamp is controlled according to door lock/unlock state
Function
Description
Refer
JMKIB3553GB
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-663
< SYSTEM DESCRIPTION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*: Even with a registered Intelligent Key remaining inside the vehicle, door locks can be unlocked from outside of the vehicle with a spare
Intelligent Key as long as key IDs are different.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of door lock/unlock function
is in the range of approximately 80 cm (31.50 in) surrounding the
driver, passenger door handles (1) and back door handle (2). How-
ever, this operating range depends on the ambient conditions.
SELECTIVE UNLOCK FUNCTION (DOOR REQUEST SWITCH)
Lock Operation
When lock signal is sent from door request switch, all doors are locked.
Unlock Operation
• When unlock signal from front door request switch (driver side) is transmitted, driver door unlocks. When
front door request switch (driver side) is operated again within 60
*
seconds, passenger door and rear door
unlock.
• When unlock signal from front door request switch (passenger side) is transmitted, passenger door unlock.
When front door request switch (passenger side) is operated again within 60
*
seconds, all doors unlocks.
*
: Default value is 60 seconds. This time changes according to auto door lock function operation time.
How to Change Selective Unlock Function Operation Mode
Selective unlock function operation mode can be changed using CONSULT.
Refer to
DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
REMINDER FUNCTION (DOOR REQUEST SWITCH)
When doors are locked or unlocked by door request switch, BCM blinks hazard warning lamps as a reminder
and transmits Intelligent Key warning buzzer request signal to Intelligent Key warning buzzer or horn reminder
signal to IPDM E/R via CAN communication. Reminder function does not operate if ignition switch in ON posi-
tion. The reminder function has C mode and S mode.
*1
: Work support mode [ANSWER BACK I-KEY LOCK UNLOCK] setting is [BUZZER]
*2
: Work support mode [ANSWER BACK I-KEY LOCK UNLOCK] setting is [HORN]
How to Change Reminder Function Operation Mode
Each door request switch operation
Operation condition
Lock
• All doors are closed
• Selective unlock function is not operating
• P position warning is not activated
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area
*
Unlock
(One touch unlock function is setting in OFF)
• Vehicle speed: 0 km/h
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area
*
JMKIA4534ZZ
Operation
C mode
S mode
Door request switch
Lock
Unlock
Lock
Unlock
Hazard warning lamp
Twice
Once
Twice
–
Intelligent Key warning
buzzer
*1
Twice
Once
–
–
Horn
*2
Once
–
–
–
DLK-664
< SYSTEM DESCRIPTION >
[TYPE 5]
SYSTEM (INTELLIGENT KEY SYSTEM)
With CONSULT
Reminder function operation mode can be changed using CONSULT.
Refer to
DLK-676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
Without CONSULT
When lock and unlock signal are sent from the Intelligent Key for more than 4 seconds at the same time, the
hazard and buzzer reminder mode is changed and hazard warning lamp blinks and horn sounds as per the fol-
lowing items:
AUTO DOOR LOCK FUNCTION
After door is unlocked by door request switch operation and if 60 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
676, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)"
.
DOOR LOCK STATUS INDICATOR OPERATION
• Door lock status indicator turns indicator lamp ON or OFF and indicates door lock or unlock state.
• For door lock status indicator operation, refer to
.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
BACK DOOR OPEN FUNCTION
JMKIB1365GB
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed
Door lock function
In
te
lli
ge
nt K
e
y
Rem
o
te
ke
yle
s
s e
n
tr
y re
ce
iv
er
Do
or swi
tch
Doo
r re
qu
es
t s
w
itc
h
Do
or lo
ck
ac
tu
at
o
r
In
si
de
key an
ten
n
a
O
u
tsi
d
e
ke
y
an
ten
n
a
CAN c
o
m
m
uni
ca
tio
n
sy
st
em
BCM
Hazard warning
lamp
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
Com
b
ina
tio
n me
ter
Door lock/unlock function
×
×
×
×
×
×
×
×
Reminder function
×
×
×
×
Door lock status indicator operation
×
Selective unlock function
×
×
×
×
×
×
Auto door lock function
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст