Nissan Qashqai J11. Manual — part 1266
HOOD
DLK-333
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm [in]
*: No more than 2 times left to right or right to left.
Fitting Adjustment Procedure
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove hood lock assembly.
3.
Adjust the surface height of hood assembly, front fender assembly, and front combination lamp according
to the specified value, by rotating hood bumper rubber (body side).
4.
Loosen hood hinge mounting bolts.
5.
Adjust clearance of hood according to the specified value, by moving the hood assembly.
6.
Tighten hood hinge mounting bolts to the specified torque.
7.
Move hood lock assembly laterally until the center of primary striker and hood lock assembly are vertical
when viewed from the front.
8.
Position hood lock assembly and engage primary striker. Check hood lock assembly and primary striker
for looseness.
9.
Tighten hood lock assembly mounting bolts and nut to the specified torque.
10. Rotate bumper rubber 1/2 of a rotation counterclockwise in upward direction.
11. After adjusting, check that hood opens and closes normally. Refer to
.
12. Install front grille. Refer to
EXT-26, "Removal and Installation"
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000010478232
REMOVAL
1.
Remove hood assembly. Refer to
DLK-331, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove upper mounting bolt of front fender assembly. Refer to
DLK-342, "Removal and Installation"
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Apply touch-up paint to the body color if the paint around the hinge is peeled off during removal.
• After installation, perform hood fitting adjustment. Refer to
DLK-331, "HOOD ASSEMBLY : Adjust-
• Before installation of hood, apply anticorrosive agent onto the mounting surface of the hood hinge.
• Check hood hinge rotating part for poor lubrication. Refer to
DLK-334, "HOOD HINGE : Inspection"
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front combination
lamp
A – A
C
Clearance
4.0 – 9.0
[0.157 – 0.354]
≤
3.0
[0.118]
D Surface height
0.0
[0.000]
—
Hood – Front fender
B – B
E
Clearance
*
—
F Surface height
≤
3.0
[0.118]
—
DLK-334
< REMOVAL AND INSTALLATION >
[TYPE 2]
HOOD
HOOD HINGE : Inspection
INFOID:0000000010478233
Check hood hinge rotating part for poor lubrication. Apply body
grease if necessary.
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000010478234
REMOVAL
CAUTION:
Two workers are required to support the hood.
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported with appropriate material when removing
hood assembly.
2.
Remove hood support rod from hood rod grommet.
3.
Remove hood rod grommet from hood assembly.
INSTALLATION
Install in the reverse order of removal.
HOOD INSULATOR
HOOD INSULATOR : Removal and Installation
INFOID:0000000010478235
REMOVAL
1.
Fully open hood assembly.
2.
Remove hood rod clamp from hood assembly.
3.
Remove hood insulator clips, and then remove hood insulator.
INSTALLATION
Install in the reverse order of removal.
: Body grease
JMKIB2933ZZ
RADIATOR CORE SUPPORT
DLK-335
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
HRA2DDT
HRA2DDT : Exploded View
INFOID:0000000011734385
HRA2DDT : Removal and Installation
INFOID:0000000010478237
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-361, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
.
10. Remove A/C pipe bracket mounting bolt.
• For Europe: Refer to Refer to
.
• Except for Europe: Refer to Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
JMKIB3298GB
DLK-336
< REMOVAL AND INSTALLATION >
[TYPE 2]
RADIATOR CORE SUPPORT
INSTALLATION
Install in the reverse order of removal.
MR16DDT
MR16DDT : Exploded View
INFOID:0000000011734386
MR16DDT : Removal and Installation
INFOID:0000000011733748
REMOVAL
1.
Remove front grille. Refer to
EXT-26, "Removal and Installation"
2.
Remove air duct (inlet). Refer to
EM-149, "Removal and Installation"
.
3.
Remove hood switch.
a.
Disconnect hood switch harness connector.
b.
Remove hood switch mounting bolt, and then remove hood switch.
4.
Remove hood lock assembly. Refer to
DLK-361, "HOOD LOCK : Removal and Installation"
.
5.
Remove hood lock control cable fixing clips from radiator core support upper. Refer to
6.
Remove engine room harness fixing clips from radiator core support upper.
7.
Remove crash zone sensor. Refer to
SR-24, "Removal and Installation"
.
8.
Remove horn. Refer to
HRN-7, "Removal and Installation"
9.
Remove radiator mounting bracket. Refer to
1.
Radiator core support upper
2.
Air guide RH
3.
Air lower guide
4.
Air guide LH
:N·m (kg-m, ft-lb)
JMKIB3299GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст