Nissan Qashqai J11. Manual — part 1208
INTELLIGENT KEY WARNING BUZZER
DLK-101
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY WARNING BUZZER
Component Function Check
INFOID:0000000010434609
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key warning buzzer is OK.
NO
>> Refer to
DLK-101, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010434610
1.
CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between Intelligent Key warning buzzer harness connector and ground.
Monitor item
Status
OUTSIDE BUZZER
ON
Outside warning buzzer
Buzzer sounds
OFF
Buzzer does not sound
(+)
(–)
Condition
Voltage
Intelligent Key warning buzzer
Connector
Terminal
E7
1
Ground
Operate Intelligent Key
buzzer
9 – 16 V
BCM
Intelligent Key warning buzzer
Continuity
Connector
Terminal
Connector
Terminal
E60
164
E7
1
Existed
BCM
Ground
Continuity
Connector
Terminal
E60
164
Not existed
DLK-102
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010434574
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (driver side) connector.
2.
Check continuity between BCM harness connector and outside key antenna (driver side) harness connec-
tor.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
100
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
120
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1348GB
JSMIA1406GB
JSMIA1507GB
JSMIA1506GB
OUTSIDE KEY ANTENNA
DLK-103
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010434574
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (driver side) connector.
2.
Check continuity between BCM harness connector and outside key antenna (driver side) harness connec-
tor.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
100
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
120
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1348GB
JSMIA1406GB
JSMIA1507GB
JSMIA1506GB
DLK-104
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
OUTSIDE KEY ANTENNA
YES
>> Replace outside handle grip RH.
NO
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010434572
1.
CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK OUTSIDE KEY ANTENNA CIRCUIT
1.
Disconnect BCM connector and outside key antenna (passenger side) connector.
2.
Check continuity between BCM harness connector and outside key antenna (passenger side) harness
connector.
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M69
118
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
119
Ground
When ignition switch
and any door switch is
ON
When Intelligent Key
is not in the antenna
detection area
When Intelligent Key
is in the antenna de-
tection area
JSMIA1507GB
JSMIA1506GB
JSMIA1507GB
JSMIA1506GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст