Nissan Qashqai J11. Manual — part 91
ROCKER COVER
EM-303
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
ROCKER COVER
Exploded View
INFOID:0000000010287217
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010287218
REMOVAL
1.
Remove air cleaner case. Refer to
2.
Remove inlet tube and air inlet hose. Refer to
3.
Remove high pressure protection cover (upper). Refer to
.
4.
Remove electric throttle control actuator.
5.
Remove fuel injector. Refer to
6.
Remove rocker cover.
• Loosen holding bolts in the reverse order as shown in the fig-
ure and remove.
INSTALLATION
E1BIA0908GB
1.
Blow-by hose
2.
Rocker cover
3.
Gasket
4.
Camshaft position sensor
5.
O-ring
A.
To turbocharger air inlet pipe
: Engine front
JPBIA3119ZZ
EM-304
< REMOVAL AND INSTALLATION >
[K9K]
ROCKER COVER
1.
Apply liquid gasket on locations shown in the figure.
• Use Genuine Liquid gasket or equivalent.
2.
Tighten holding bolts in the numerical order as shown in the fig-
ure.
3.
Install in the reverse order of removal after this steps.
MBIB0581E
: Engine front
: 12 N·m (1.2 kg-m, 9 ft-lb)
JPBIA3119ZZ
TIMING BELT
EM-305
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
TIMING BELT
Exploded View
INFOID:0000000010287219
Refert to
for symbol marks in the figure
Removal and Installation
INFOID:0000000010287220
CAUTION:
• Apply new engine oil to parts marked in illustration before installation.
• Replace any belt that has been removed.
• Never turn the engine in the direction opposite to that of normal operation.
• When replacing the timing belt, be sure to replace the timing belt tensioner.
• Never run the engine without the drive belts to avoid damaging the crankshaft pulley.
REMOVAL
1.
Disconnect battery cable from the negative terminal.
2.
Remove front wheel RH.
3.
Remove fender protector RH. Refer to
4.
Remove drive belt, and auto-tensioner. Refer to
EM-273, "Removal and Installation"
5.
Remove RH engine torque rod.
JPBIA3140GB
1.
Timing belt inner cover
2.
Timing belt
3.
Camshaft sprocket
4.
Timing belt tensioner
5.
Timing belt upper cover
6.
Timing belt lower cover
7.
Cylinder head suspended bracket
8.
Crankshaft pulley
9.
Crankshaft sprocket
10. Rear oil seal
11.
Rear oil seal retainer
12. Gasket
A
Comply with the assembly proce-
dure when tightening. Refer to
B
Comply with the assembly proce-
dure when tightening. Refer to
EM-306
< REMOVAL AND INSTALLATION >
[K9K]
TIMING BELT
6.
Remove RH engine mounting.
7.
Remove RH engine mounting support bracket and RH engine mounting insulator.
8.
Remove upper timing cover, camshaft position sensor and cylin-
der head suspended mounting bracket.
9.
Remove timing belt lower cover.
10. Remove the TDC pin bolt.
11. Rotate the crankshaft clockwise, until the position (A) of the
camshaft pulley becomes opposite of the position (B) on the cyl-
inder head.
MBIB1041E
MLIA0003E
MBIB0392E
MBIB1923E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст