Nissan Qashqai J11. Manual — part 1658
COMPONENT PARTS
MIR-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Door mirror open relay
• Power supply is supplied to motor when door mirror is opening.
• This is the ground circuit when auto retractable door mirror is operating.
Door mirror close relay
• Power supply is supplied to motor when door mirror is closed.
• Power supply is supplied to motor when auto retractable door mirror is operating.
Door mirror remote control switch (mir-
ror switch)
It supplies power to mirror motor through mirror switch and changeover switch.
Door mirror remote control switch
(changeover switch)
It transmits the LH/RH control of door mirror that supplies power supply.
Door mirror motor
It makes mirror face operate from side to side and up and down via integrated motor.
Steering switch
Transmits steering switch signal to combination meter.
Combination meter
Displays the system status according to signal received.
Transmits auto retractable door mirror setting signal to the BCM via CAN communication.
Item
Function
MIR-8
< WIRING DIAGRAM >
DOOR MIRROR SYSTEM
LHD MODELS : Wiring Diagram - DOOR MIRROR (WITHOUT ELECTRIC FOLD-
JRLWD2212GB
OPERATION
MIR-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OPERATION
Menu Displayed by Pressing Each Switch
INFOID:0000000011733526
JMLIA6154ZZ
No.
Function name
Description
Auto fold Off
Non
−
operating auto retractable door mirror.
Unfold at Ignition
Door mirror open when ignition switch ON.
Unfold at Unlock
Door mirror open when door lock signal is received from intelligent Key or door request
switch.
MIR-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000011405203
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Exterior lamp
HEAD LAMP
×
×
×
Interior room lamp control
INT LAMP
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
PTC heater control
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
Interior room lamp battery saver
BATTERY SAVER
×
Back door open
TRUNK
×
Vehicle security
THEFT ALM
×
×
RAP
RETAINED PWR
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст