Nissan Qashqai J11. Manual — part 760
CVT FLUID
TM-615
< PERIODIC MAINTENANCE >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
34. Select “Data Monitor” in “TRANSMISSION” using CONSULT.
35. Select “CONFORM CVTF DETERIORTN”.
36. Select “Erase”.
37. Perform air bleeding of electric oil pump. Refer to
38. Stop the engine.
Adjustment
INFOID:0000000010245673
CAUTION:
• During adjustment of the CVT fluid level, check CONSULT so that the oil temperature may be main-
tained from 35 to 45
°
C (95 to 113
°
F).
• During adjustment of the CVT fluid level, check that the engine speed is maintaining 500 rpm.
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.
1.
Check that the selector lever is in the “P” position, then completely engage the parking brake.
2.
Start the engine.
3.
Adjust the CVT fluid temperature to be approximately 40
°
C (104
°
F).
NOTE:
The CVT fluid is largely affected by temperature. Therefore be sure to use CONSULT and check the
“FLUID TEMP” under “TRANSMISSION” in “Data Monitor” while adjusting.
4.
While depressing the brake pedal, shift the selector lever to the entire position from “P” to “D”, and shift it
to the “P” position.
NOTE:
Hold the lever at each position for 5 seconds.
5.
Lift up the vehicle.
6.
Check that there is no CVT fluid leakage.
7.
Remove the overflow plug
from converter housing.
8.
Install the charging pipe set (KV311039S0) (A) into the overflow
plug hole.
CAUTION:
Tighten the charging pipe by hand.
9.
Install the ATF changer hose (B) to the charging pipe.
CAUTION:
Press the ATF changer hose all the way onto the charging
pipe until it stops.
10. Fill approximately 0.5 liter (1/2 lmp qt) of the CVT fluid.
11. Remove the ATF changer hose from the charging pipe, and
check that the CVT fluid drains out from the charging pipe. If it
does not drain out, perform charging again.
CAUTION:
Perform this work with the vehicle idling.
12. When the flow of CVT fluid slows to a drip, remove the charging pipe from the converter housing.
13. Tighten the overflow plug to the specified torque. Refer to
.
CAUTION:
Never reuse O-ring.
Recommended fluid and fluid capacity
: Refer to
MA-59, "Fluids and Lubricants"
: Vehicle front
JSDIA3714ZZ
JSDIA3713ZZ
TM-616
< PERIODIC MAINTENANCE >
[CVT: RE0F10G]
CVT FLUID
14. Lift down the vehicle.
15. Stop the engine.
CVT SHIFT SELECTOR
TM-617
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000010245674
Removal and Installation
INFOID:0000000010245675
CAUTION:
Always apply the parking brake before removal and installation.
REMOVAL
1.
Apply the parking brake.
CAUTION:
Make sure the vehicle cannot move with the parking brake applied.
2.
Turn ignition switch ON.
3.
Shift the selector lever to “N” position.
4.
Turn ignition switch OFF.
5.
Remove the shift selector knob with the following procedure.
Selector lever knob
Lock pin
Selector lever knob cover
Position indication panel
CVT shift selector assembly
Park position switch
Shift lock unit
Detent switch*
Position indicator bulb
: N·m (kg-m, in-lb)
*: With push engine starter
JSDIA5217GB
TM-618
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
CVT SHIFT SELECTOR
a.
Slide the selector lever knob cover
down.
CAUTION:
Never damage the knob cover.
b.
Pull out the lock pin
from the selector lever knob
.
c.
Pull the selector lever knob and the selector lever knob cover
upwards to remove them.
6.
Remove the center console. Refer to
.
7.
Shift the selector lever to “P” position.
8.
Disconnect the tip
of control cable and remove socket
from
the CVT shift selector assembly.
9.
Disconnect the CVT shift selector connector
.
10. Remove the CVT shift selector assembly from the vehicle.
INSTALLATION
Note the followings and install in the reverse order of removal.
• Pay attention to the following when connecting the control cable to the CVT shift selector assembly.
1.
When connecting the control cable
to the CVT shift selector
assembly
, face the grooved surface of the rib
up and insert
the control cable until it stops.
NOTE:
Apply multi-purpose grease to control cable eye before installa-
tion.
JSDIA2778ZZ
JSDIA4220ZZ
JSDIA5384ZZ
JSDIA1624ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст