Nissan Qashqai J11. Manual — part 637
FINAL DRIVE
TM-123
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
FINAL DRIVE
Exploded View
INFOID:0000000010428798
.
Disassembly
INFOID:0000000010428799
Assembly
INFOID:0000000010428800
.
Adjustment
INFOID:0000000010478355
Adjusting the pretension of the differential bearings
1.
Fit the differential.
2.
Measure the distance (X1) between the end of the bearing hous-
ing and the joint face.
3.
Remove the differential.
4.
Measure the distance (X2) between the mechanism housing
joint face and the bearing face that takes the permanent shim.
5.
Determine the thickness of the permanent shim using the following procedure, accounting for a preten-
sioning determined by a value between 0.15mm (0.006 In) and 0.21 mm (0.008 In).
a.
Permanent shim = (X2 - X1) + pretensioning
b.
Example:
• X1 = 26.49 mm (1.043 In)
• X2 = 26.98 mm (1.062 In)
• Permanent shim = (26.98 - 26.49) + 0.18 = 0.67 mm (0.026 In)
Given that shims vary by 0.04 mm (0.002 In), in this example, it is necessary to use the 0.68 mm (0.027
In) shim in the set.
NOTE:
In some cases, two shims are required to obtain the correct pretensioning torque.
Example: Calculated value 1.04 mm - shims available 0.48 + 0.56 = 1.04 mm (0.041)
E1DIA0326ZZ
E1DIA0327ZZ
TM-124
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
FINAL DRIVE
Inspection
INFOID:0000000010428801
GEAR, WASHER, SHAFT AND CASE
Check side gears, thrust washer, pinion mate shaft, pinion mate
gears, lock ring and differential case. If necessary, replace with a
new one.
BEARING
Check for bearing damage and rough rotation. If necessary, replace
with a new one.
CAUTION:
When replacing tapered roller bearing, replace outer and inner
races as a set.
PCIB0977J
SPD715
SHIFT FORK AND FORK ROD
TM-125
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT FORK AND FORK ROD
Exploded View
INFOID:0000000010428802
.
Disassembly
INFOID:0000000010428803
for disassembly procedure.
Assembly
INFOID:0000000010428804
for assembly procedure.
Inspection
INFOID:0000000010428805
FORK ROD AND SHIFT FORK
Check contact surface and sliding surface of fork rod and shift fork
for wear, damage, and bend. Replace if necessary.
SCIA7785E
TM-126
< SERVICE DATA AND SPECIFICATIONS (SDS)
[6MT: RS6F95R]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000010428806
TRANSAXLE
FINAL GEAR
Engine type
R9M
Transaxle model
RS6F95R
Model code number
4EA2A
Number of speeds
6
Synchromesh type
Warner
Shift pattern
Gear ratio
1st
3.727
2nd
2.043
3rd
1.323
4th
0.947
5th
0.723
6th
0.596
Reverse
3.641
Number of teeth
Input gear
1st
11
2nd
23
3rd
31
4th
38
5th
47
6th
52
Reverse
11
Main gear
1st
41
2nd
47
3rd
41
4th
36
5th
34
6th
31
Reverse
39
Reverse idler gear
Input/Output
38/37
Oil capacity
(Imp pt)
Approx. 1.8 (1.6)
Remarks
Reverse synchronizer
Installed
Triple-cone synchronizer
1st and 2nd
PCIB1769E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст