Nissan Qashqai J11. Manual — part 1368
HAZARD FUNCTION
DLK-741
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD FUNCTION
Component Function Check
INFOID:0000000010672356
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “FLASHER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-741, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010672357
1.
CHECK HAZARD OPERATION
EXL-26, "TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description"
(LED
headlamp models) or
EXL-195, "TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Descrip-
(halogen headlamp models).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
(LED headlamp models) and
(halogen headlamp models).
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
FLASHER
LH
Front turn signal lamp LH
Turns ON
RH
Front turn signal lamp RH
Turns ON
OFF
Front turn signal lamp
Turns OFF
DLK-742
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
INFORMATION DISPLAY
INFORMATION DISPLAY
Diagnosis Procedure
INFOID:0000000010672358
1.
CHECK COMBINATION METER
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
INTELLIGENT KEY BATTERY
DLK-743
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Component Inspection
INFOID:0000000010672359
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA. Refer to
.
Is the measurement value within the specification?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key battery.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
DLK-744
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 5]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Component Function Check
INFOID:0000000010672360
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Intelligent Key warning buzzer is OK.
NO
>> Refer to
DLK-744, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010672361
1.
CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Check voltage between Intelligent Key warning buzzer harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between Intelligent Key warning buzzer harness connector and ground.
Monitor item
Status
OUTSIDE BUZZER
ON
Outside warning buzzer
Buzzer sounds
OFF
Buzzer does not sound
(+)
(–)
Condition
Voltage
Intelligent Key warning buzzer
Connector
Terminal
E7
1
Ground
Operate Intelligent Key
buzzer
9 – 16 V
BCM
Intelligent Key warning buzzer
Continuity
Connector
Terminal
Connector
Terminal
E60
164
E7
1
Existed
BCM
Ground
Continuity
Connector
Terminal
E60
164
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст