Nissan Qashqai J11. Manual — part 1740
EXL-262
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
B20D1 HEADLAMP (LO) RH POWER SUPPLY CIRCUIT
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK HEADLAMP (LO) RH POWER SUPPLY
With CONSULT
1.
Connect IPDM E/R connector.
2.
Turn ignition switch ON
3.
Select “HEADLAMP (LO)” in “Active Test” mode of “IPDM E/R” using CONSULT.
4.
With operating the test items, check the voltage between headlamp low RH harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
3.
CHECK HEADLAMP (LO) RH
Check the headlamp (LO) RH bulb. Refer to
EXL-262, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace headlamp (LO) RH bulb. Refer to
.
Component Inspection
INFOID:0000000010469952
1.
CHECK HEADLAMP (LO) RH BULB
1.
Turn ignition switch OFF.
2.
Disconnect headlamp low RH connector.
3.
Check resistance of headlamp (LO) RH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace headlamp (LO) RH bulb. Refer to
.
IPDM E/R
—
Continuity
Connector
Terminal
E101
54
Ground
Not existed
+
-
Test item
Voltage
Headlamp low LH
Connector
Terminal
E97
1
Ground
HEADLAMP
(LO)
On
9 – 16 V
Off
0 – 1 V
Headlamp (LO) RH
Resistance
Terminal
1
2
Except 0
Ω
B20D2 PARKING LAMP POWER SUPPLY CIRCUIT
EXL-263
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
B20D2 PARKING LAMP POWER SUPPLY CIRCUIT
DTC Description
INFOID:0000000010469953
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Front combination lamp LH internal circuit
- LED (Parking lamp)
- Control circuit
- Harness
• Front combination lamp RH internal circuit
- LED (parking lamp)
- Control circuit
- Harness
• IPDM E/R
FAIL-SAFE
Shuts off the power supply to the parking lamp (LH/RH) power supply circuit until the parking lamp, license
plate lamp, and tail lamp ON conditions are no longer satisfied.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
With CONSULT
1.
Turn ignition switch ON.
2.
Select “P LAMP CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R” using CONSULT.
3.
Check the monitor status.
What is the monitor status?
“0”
>> GO TO 2.
“1”
>> A short circuit is detected multiple times in the parking lamp LH or parking lamp RH power supply
circuit, and damage accumulates at the smart FET inside the IPDM E/R. For this reason, IPDM E/
R does not turn ON the smart FET. Because the DTC cannot be reproduced in this state, perform
EXL-264, "Diagnosis Procedure"
and replace IPDM E/R after the malfunctioning part is repaired.
PCS-67, "Removal and Installation"
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF.
2.
Turn ignition switch ON.
3.
Turn lighting switch 1ST.
4.
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
5.
Check DTC.
Is DTC detected?
YES
>> Refer to
EXL-264, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
B20D2
PARKING LAMP PWR SPLY CIRC
(Parking lamp power supply circuit)
[CIRC
SHORT TO
GRND]
When the parking lamp, license plate lamp, and tail lamp
ON conditions are satisfied (smart FET inside IPDM E/R
is ON), and overcurrent is detected in the parking lamp LH
power supply circuit or parking lamp RH power supply cir-
cuit.
Monitor item
Monitor status
P LAMP CIRC MALFUNCTN
0
1
EXL-264
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
B20D2 PARKING LAMP POWER SUPPLY CIRCUIT
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010469954
1.
CHECK PARKING LAMP POWER SUPPLY CIRCUIT (SHORT)
1.
Turn ignition switch OFF.
2.
Turn lighting switch OFF.
3.
Disconnect IPDM E/R connector and front combination lamp connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK PARKING LAMP POWER SUPPLY
With CONSULT
1.
Connect IPDM E/R connector.
2.
Turn ignition switch ON
3.
Select “PARKING LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
4.
With operating the test items, check the voltage between front combination lamp harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
3.
CHECK PARKING LAMP
Check the parking lamp. Refer to
EXL-264, "Component Inspection"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the corresponding front combination lamp. Refer to
EXL-318, "Removal and Installation"
.
Component Inspection
INFOID:0000000010469955
1.
CHECK PARKING LAMP
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp connector.
3.
Check resistance of front combination lamp terminals.
Parking lamp LH
IPDM E/R
—
Continuity
Connector
Terminal
RH
E101
53
Ground
Not existed
LH
E102
64
+
-
Test item
Voltage
Front combination lamp
Connector
Terminal
RH
E92
3
Ground
PARKING
LAMP
On
9 – 16 V
Off
0 – 1 V
LH
E90
On
9 – 16 V
Off
0 – 1 V
Front combination lamp LH
Resistance
Terminal
3
1
Except 0
Ω
B20D2 PARKING LAMP POWER SUPPLY CIRCUIT
EXL-265
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Parking lamp RH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the corresponding front combination lamp. Refer to
EXL-318, "Removal and Installation"
.
Front combination lamp RH
Resistance
Terminal
3
1
Except 0
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст