Nissan Qashqai J11. Manual — part 1706
LICENSE PLATE LAMP CIRCUIT
EXL-125
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000010338812
1.
CHECK TAIL LAMP LH OPERATION
Check that tail lamp LH is turned ON when lighting switch is turned 1ST.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-123, "Component Function Check"
.
2.
CHECK LICENSE PLATE LAMP OPERATION
With CONSULT
1.
Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
EXL-125, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338813
1.
CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and license plate lamp connector.
3.
Check continuity between IPDM E/R harness connector and license plate lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK LICENSE PLATE LAMP GROUND CIRCUIT
Check continuity between license plate lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP BULB
Check the applicable license plate lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding license plate lamp bulb socket. Repair or replace if necessary.
NO
>> Replace the corresponding license plate lamp bulb. Refer to
.
On
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
License plate lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E37
4
D97
1
Existed
LH
D96
License plate lamp
—
Continuity
Connector
Terminal
RH
D97
2
Ground
Existed
LH
D96
EXL-126
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
DAYTIME RUNNING LIGHT CIRCUIT
DAYTIME RUNNING LIGHT CIRCUIT
Component Function Check
INFOID:0000000010338814
1.
CHECK DAYTIME RUNNING LIGHT OPERATION
With CONSULT
1.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the daytime running light is turned ON.
Is the inspection result normal?
YES
>> Daytime running light circuit is normal.
NO
>> Refer to
EXL-126, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338815
1.
CHECK DAYTIME RUNNING LIGHT OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp connector.
3.
Turn ignition switch ON.
4.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
5.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
2.
CHECK DAYTIME RUNNING LIGHT POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DAYTIME RUNNING LIGHT GROUND CIRCUIT
Check continuity between front combination lamp harness connector and ground.
On
: Daytime running light ON
Off
: Daytime running light OFF
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E101
50
Ground
DAYTIME RUN-
NING LIGHT
On
9 – 16 V
Off
0 – 1 V
LH
E102
57
On
9 – 16 V
Off
0 – 1 V
IPDM E/R
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E101
50
E93
4
Existed
LH
E102
57
E91
DAYTIME RUNNING LIGHT CIRCUIT
EXL-127
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Replace the corresponding front combination lamp. Refer to
EXL-161, "Removal and Installation"
.
NO
>> Repair or replace harness.
Front combination lamp
—
Continuity
Connector
Terminal
RH
E93
6
Ground
Existed
LH
E91
EXL-128
< DTC/CIRCUIT DIAGNOSIS >
[LED HEADLAMP]
STOP LAMP CIRCUIT
STOP LAMP CIRCUIT
Component Function Check
INFOID:0000000010338817
1.
CHECK STOP LAMP OPERATION
1.
Turn ignition switch ON.
2.
With operating the brake pedal, check that the stop lamp and high-mounted stop lamp is turned ON.
Is the inspection result normal?
YES
>> Stop lamp circuit is normal.
NO
>> Refer to
EXL-128, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010338818
1.
CHECK SYMPTOM
Check symptom (A or B)
Which symptom is detected?
A
>> GO TO 2.
B
>> GO TO 7.
2.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
3.
CHECK BCM POWER SUPPLY (STOP LAMP)
1.
Disconnect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK STOP LAMP SWITCH POWER SUPPLY
1.
Disconnect stop lamp switch connector.
Depressed
: Stop lamp and high-mounted stop lamp
ON
Fully re-
leased
: Stop lamp and high-mounted stop lamp
OFF
Symptom
A
All of stop lamp and high-mounted stop lamp are not turned ON
B
Any of stop lamp and high-mounted stop lamp are not turned ON
Unit
Location
Fuse No.
Capacity
• BCM
• Stop lamp switch
Fuse block (J/B)
#24
10 A
+
-
Voltage
BCM
Connector
Terminal
M68
145
Ground
9 – 16 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст