Nissan Qashqai J11. Manual — part 1302
FRONT DOOR
DLK-477
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Apply anticorrosive agent onto the mounting surface.
• After installation, perform the fitting adjustment. Refer to
DLK-477, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• Check door hinge and door check link rotating part for poor lubrication.
- Door hinge: Refer to
DLK-479, "DOOR HINGE : Inspection"
.
- Door check link: Refer to
DLK-479, "DOOR CHECK LINK : Removal and Installation"
.
DOOR ASSEMBLY : Adjustment
INFOID:0000000010479356
FITTING ADJUSTMENT
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Always replace after every disassembly.
JMKIB3256GB
DLK-478
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR
Fitting Adjustment Standard
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove front fender. Refer to
DLK-474, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on vehicle body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Apply body grease if necessary. Refer to
DLK-479, "DOOR HINGE : Inspection"
8.
Install front fender. Refer to refer to
DLK-474, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010479357
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-477, "DOOR ASSEMBLY : Adjust-
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010479358
REMOVAL
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front fender – Front door
A – A
H
Clearance
3.3 – 5.3
[0.130 – 0.209]
I
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
FRONT DOOR
DLK-479
< REMOVAL AND INSTALLATION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-474, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-476, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-477, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010479359
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010479360
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove front door speaker.
a.
Disconnect front door speaker harness connector.
b.
Remove front door speaker mounting bolts, and then remove front door speaker.
4.
Remove check link mounting bolts of vehicle body side.
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
: Body grease
JMKIB0321ZZ
DLK-480
< REMOVAL AND INSTALLATION >
[TYPE 3]
FRONT DOOR
DOOR CHECK LINK : Inspection
INFOID:0000000010479361
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст