Nissan Qashqai J11. Manual — part 957
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
BRC-65
< BASIC INSPECTION >
[WITH ESP]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• ECM: Refer to
Are the memories erased?
YES
>> Inspection End.
NO
>> Check the items indicated by the self-diagnosis.
BRC-66
< BASIC INSPECTION >
[WITH ESP]
CALIBRATION OF DECEL G SENSOR
CALIBRATION OF DECEL G SENSOR
Description
INFOID:0000000010428742
CAUTION:
Always perform the decel G sensor calibration before driving when the following operation is per-
formed.
NOTE:
Yaw rate/side/decel G sensor calibration is performed when performing the decel G sensor calibration.
×
: Required —: Not required
Work Procedure
INFOID:0000000010428743
Decel G sensor calibration
CAUTION:
Always use CONSULT for the decel G sensor calibration. (It cannot be adjusted other than with CON-
SULT.)
NOTE:
Yaw rate/side/decel G sensor calibration is performed when performing the decel G sensor calibration.
1.
CHECK THE VEHICLE STATUS
1.
Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.
2.
Stop the engine.
3.
Turn the ignition switch OFF.
Is the vehicle stopped in the straight-ahead position on level surface?
YES
>> GO TO 2.
NO
>> Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.
2.
PERFORM DECEL G SENSOR CALIBRATION
CAUTION:
• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start engine.
2.
Select “ABS”, “WORK SUPPORT”, “DECEL G SEN CALIBRATION” in this order.
3.
Select “START”.
4.
After approx. 10 seconds, select “END”.
5.
Turn ignition switch OFF and then turn it ON again.
CAUTION:
Be sure to perform the operation above.
>> GO TO 3.
Procedure
Decel G sensor calibration
Removing/ installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/installing steering components
—
Replacing steering components
—
Removing/installing suspension components
—
Replacing suspension components
—
Removing/installing tire
—
Replacing tire
—
Tire rotation
—
Adjusting wheel alignment.
—
CALIBRATION OF DECEL G SENSOR
BRC-67
< BASIC INSPECTION >
[WITH ESP]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
3.
CHECK DATA MONITOR
With CONSULT
1.
Drive the vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level sur-
face.
2.
Select “ABS”, “DATA MONITOR”, “ECU INPUT SIGNALS” and “DECEL G SENSOR” in this order. Check
that the signal is within the specified value.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 1.
4.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
Erase self-diagnosis result of “ABS”.
Are the memories erased?
YES
>> Inspection End.
NO
>> Check the items indicated by the self-diagnosis.
DECEL G SENSOR
: Approx.
±
0.01 G
BRC-68
< BASIC INSPECTION >
[WITH ESP]
CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)]
CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
Work Procedure
INFOID:0000000010763725
CAUTION:
• Use “Manual Configuration” only when “TYPE ID” of ABS actuator and electric unit (control unit)
cannot be read.
• After configuration, turn the ignition switch from OFF to ON and check that the VDC warning lamp
turns OFF after staying illuminated for approximately two seconds.
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search ABS actuator and electric unit (control unit) of the applicable
vehicle and find “Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for ABS actuator and electric unit (control unit). Replace in the
usual manner. Refer to
BRC-142, "Removal and Installation"
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “Before Replace ECU” of “Read/Write Configuration”.
2.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) (1)
Replace ABS actuator and electric unit (control unit). Refer to
BRC-142, "Removal and Installation"
CAUTION:
Never perform the following work items:
• Air bleeding
• Adjustment of steering angle sensor neutral position
• Calibration of decel G sensor
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст