Nissan Qashqai J11. Manual — part 209
ECH-134
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
B1900 DC/DC CONVERTER
B1900 DC/DC CONVERTER
DTC Logic
INFOID:0000000010500813
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If the other DTC Confirmation Procedure is performed right before this procedure, the ignition switch must be
turned OFF and wait for 12 minutes or more to start this procedure.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-1
1.
Turn ignition switch ON and wait at least 3 seconds.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECH-134, "Diagnosis Procedure"
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
1.
Start the engine and warm it up to normal operating temperature.
2.
Press start/stop OFF switch and check that the switch indicator is ON.
3.
Select “AUTO STOP START” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.
4.
Touch “START” and operate stop/start system. (engine stop.)
5.
Touch “CANCEL” and restart the engine.
6.
Check DTC.
Without CONSULT
1.
Activate stop/start system. Refer to
ECH-33, "STOP/START SYSTEM : System Description"
.
CAUTION:
Always drive vehicle at a safe speed.
2.
Restart the engine.
3.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECH-134, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010500814
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the fuse fusing?
YES
>> Replace the fuse after repairing the applicable circuit.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B1900
DC/DC CONVERTER
(DC/DC converter power sup-
ply input 1 circuit)
DC/DC converter detects power supply
input 1 is 5.0 V or less and difference
between power supply input 1 and pow-
er supply input 2 is 4.0 V or more for 3
seconds.
• Harness and connectors
(DC/DC converter power supply input 1 cir-
cuit is open or shorted.)
• DC/DC converter
Fuse No.
Capacity
F/L-O
30 A
B1900 DC/DC CONVERTER
ECH-135
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
ECH
N
P
O
NO
>> GO TO 2.
2.
CHECK DC/DC CONVERTER POWER SUPPLY INPUT 1
1.
Disconnect DC/DC converter harness connector.
2.
Check the voltage between DC/DC converter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK DC/DC CONVERTER POWER SUPPLY INPUT 1 CIRCUIT
1.
Disconnect battery negative terminal.
2.
Check the continuity between DC/DC converter harness connector and fuse.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.
CHECK INTERMITTENT INCIDENT
Perform intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace DC/DC converter. Refer to
ECH-314, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
+
−
Voltage
DC/DC converter
Connector
Terminal
M23
1
Ground
Battery voltage
+
−
Continuity
DC/DC converter
Fuse No.
Connector
Terminal
M23
1
F/L-O
Existed
ECH-136
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
B1901 DC/DC CONVERTER
B1901 DC/DC CONVERTER
DTC Logic
INFOID:0000000010500815
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If the other DTC Confirmation Procedure is performed right before this procedure, the ignition switch must be
turned OFF and wait for 12 minutes or more to start this procedure.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-1
1.
Turn ignition switch ON and wait at least 3 seconds.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECH-136, "Diagnosis Procedure"
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
1.
Start the engine and warm it up to normal operating temperature.
2.
Press start/stop OFF switch and check that the switch indicator is ON.
3.
Select “AUTO STOP START” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.
4.
Touch “START” and operate stop/start system. (engine stop.)
5.
Touch “CANCEL” and restart the engine.
6.
Check DTC.
Without CONSULT
1.
Activate stop/start system. Refer to
ECH-33, "STOP/START SYSTEM : System Description"
.
CAUTION:
Always drive vehicle at a safe speed.
2.
Restart the engine.
3.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECH-136, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010500816
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the fuse fusing?
YES
>> Replace the fuse after repairing the applicable circuit.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B1901
DC/DC CONVERTER
(DC/DC converter power sup-
ply input 2 circuit)
DC/DC converter detects power supply
input 2 is 5.0 V or less and difference
between power supply input 2 and
power supply input 1 is 4.0 V or more
for 3 seconds.
• Harness and connectors
(DC/DC converter power supply input 2 cir-
cuit is open or shorted.)
• DC/DC converter
Fuse No.
Capacity
F/L-N
30 A
B1901 DC/DC CONVERTER
ECH-137
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
ECH
N
P
O
NO
>> GO TO 2.
2.
CHECK DC/DC CONVERTER POWER SUPPLY INPUT 2
1.
Disconnect DC/DC converter harness connector.
2.
Check the voltage between DC/DC converter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK DC/DC CONVERTER POWER SUPPLY INPUT 2 CIRCUIT
1.
Disconnect battery negative terminal.
2.
Check the continuity between DC/DC converter harness connector and fuse.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
4.
CHECK INTERMITTENT INCIDENT
Perform intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace DC/DC converter. Refer to
ECH-314, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
+
−
Voltage
DC/DC converter
Connector
Terminal
M23
3
Ground
Battery voltage
+
−
Continuity
DC/DC converter
Fuse No.
Connector
Terminal
M23
3
F/L-N
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст