Nissan Qashqai J11. Manual — part 856
FSU-14
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
TRANSVERSE LINK
Exploded View
INFOID:0000000010297075
1.
Strut mounting insulator
2.
Strut mounting bearing
3.
Bound bumper
4.
Coil spring
5.
Lower rubber seat
6.
Strut
7.
Steering knuckle
8.
Stabilizer connecting rod
9.
Stabilizer clamp
E1EIA0115GB
TRANSVERSE LINK
FSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
Removal and Installation
INFOID:0000000010297076
REMOVAL
1.
Remove tires from vehicle.
2.
Remove the engine undercover.
3.
Remove the steering knuckle lower bolt and nut.
4.
Remove the nut, and separate the stabilizer connecting rod (LH/RH) from the strut bracket.
5.
Remove transverse link bolts from suspension member, and remove transverse link..
NOTE:
Transverse link cannot be pulled out because the mounting bolt
(
) of transverse link at the rear of the mounting area located
on the front side of vehicle hits against the stabilizer bar. There-
fore, get stabilizer bar out of the way to remove the transverse
link.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the front suspension member, under unladen conditions with
tires on level ground.
Inspection
INFOID:0000000010297077
INSPECTION AFTER REMOVAL
Visual Inspection
Check the following:
• Transverse link and bushing for deformation, cracks or damage. Replace it if necessary.
• Ball joint boot for cracks or other damage, and also for grease leakage. Replace it if necessary.
Ball Joint Inspection
Manually move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
NOTE:
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
• Hook a spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
- If swing torque exceeds standard range, replace transverse link
assembly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
10. Stabilizer bushing
11. Stabilizer bar
12. Front suspension member
13. Rebound stopper rubber
14. Front suspension member stay
15. Transverse link
16. Rear suspension member stay
17. Front suspension member insulator
Refer to
SEIA0633J
Standard
Swing torque
Spring balance
measurement
JPEIA0005ZZ
FSU-16
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
- If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
FSU-7, "Wheel Alignment Inspection"
.
2.
Adjust neutral position of steering angle sensor. Refer to
.
Standard
Axial end play
:Refer to
.
FRONT STABILIZER
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000010297078
1.
Strut mounting insulator
2.
Strut mounting bearing
3.
Bound bumper
4.
Coil spring
5.
Lower rubber seat
6.
Strut
7.
Steering knuckle
8.
Stabilizer connecting rod
9.
Stabilizer clamp
E1EIA0115GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст