Nissan Qashqai J11. Manual — part 753
P188E ELECTRIC OIL PUMP
TM-587
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• The diode is normal if the result is as shown in the figure when the
polarity is reversed.
NOTE:
Tester specifications may vary depending on the tester type. Refer to
the handling manual of the tester before checking continuity.
JSDIA2056GB
TM-588
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P188F ELECTRIC OIL PUMP
P188F ELECTRIC OIL PUMP
DTC Logic
INFOID:0000000010249646
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION (PART 1)
With CONSULT
1.
Start the engine.
2.
Maintain stop/start system operation state for 10 seconds or more. Refer to
TEM : System Description (M/T models)"
3.
Restart the engine and drive.
4.
Maintain stop/start system operation state for 10 seconds or more again.
NOTE:
If the engine restarts automatically 10 seconds later, the system may be in fail safe.
DTC
Trouble diagnosis
name
DTC detection condition
Possible causes
P188F
Electric Oil Pump
When 1 is not satisfied and 2 and 3 are satisfied:
1.
When any of the following conditions are satisfied (di-
agnosis prohibition condition):
-
Battery voltage: 10 V or less
-
Electric oil pump relay ON is being instructed and with-
in 0.52 seconds after battery voltage recovers from the
state that is 10 V or less
-
Electric oil pump relay OFF is being instructed
-
Within 0.35 seconds after ignition switch is turned ON
-
Electric oil pump system malfunction is being deter-
mined
-
Secondary pressure sensor malfunction is being deter-
mined
2.
When all of the following conditions are satisfied and
this state is maintained for 5 seconds:
-
During idling stop
-
Secondary pressure: Less than 0.03 MPa
3.
When all of the following conditions are satisfied and
this state is maintained for 5 seconds:
-
Judgment for 2 is complete (Idling stop oil pressure
lowering judgment for the first time is complete.)
-
Electric oil pump air bleeding is complete after ignition
switch is turned OFF
-
Secondary pressure: Less than 0.03 MPa
-
None of the following items are satisfied:
•
A sudden deceleration of
−
5.88 m/s
2
(
−
0.6 G) or less is
experienced
•
Ignition switch is turned OFF after judgment of 2 is
complete
•
When all of the following conditions are satisfied and
this state is maintained for 5 seconds:
1 (diagnosis prohibition condition) is not satisfied
During idling stop
Secondary pressure: 0.03 MPa or more
• Electric oil pump
• Secondary pressure sensor
P188F ELECTRIC OIL PUMP
TM-589
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Check the DTC.
“P188F” detected?
YES
>> Go to
NO
>> GO TO 3.
3.
CHECK DTC DETECTION (PART 2)
With CONSULT
1.
Turn ignition switch OFF.
2.
Start the engine.
3.
Maintain stop/start system operation state for 10 seconds or more. Refer to
TEM : System Description (M/T models)"
4.
Restart the engine and drive.
5.
Maintain stop/start system operation state for 10 seconds or more again.
NOTE:
If the engine restarts automatically 10 seconds later, the system may be in fail safe.
6.
Check the DTC.
“P188F” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010249647
1.
AIR BLEEDING OF ELECTRIC OIL PUMP
Perform air bleeding of the electric oil pump. Refer to
.
>> GO TO 2.
2.
CHECK DTC DETECTION
Perform DTC confirmation procedure. Refer to
“P188F” detected?
YES
>> Replace the electric oil pump & motor assembly. Refer to
TM-648, "Removal and Installation"
.
NO
>> INSPECTION END
TM-590
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P1890 ELECTRIC OIL PUMP RELAY
P1890 ELECTRIC OIL PUMP RELAY
DTC Logic
INFOID:0000000010249648
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn ignition switch ON and wait for 5 seconds or more.
2.
Check the DTC.
“P1890” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010249649
1.
ELECTRIC OIL PUMP RELAY
1.
Check the electric oil pump relay. Refer to
TM-592, "Component Inspection (Electric Oil Pump Relay)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the electric oil pump relay.
2.
CHECK ELECTRIC OIL PUMP RELAY POWER CIRCUIT
Check voltage between the electric oil pump relay harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
DTC
Trouble diagnosis name
DTC detection condition
Possible causes
P1890
Electric Oil Pump Relay
When 1 is not satisfied and 2 is satisfied, and this state
is maintained for 5 seconds or more:
1.
When any of the following conditions are satis-
fied (diagnosis prohibition condition):
-
Battery voltage: 10 V or less
-
Within 0.35 seconds after ignition switch is
turned ON
-
Electric oil pump air bleed judgment: Air bleeding
in progress or air bleeding is in judgment
2.
When all of the following conditions are satisfied:
-
Electric oil pump relay OFF is being instructed
and electric oil pump duty 0 %
• Electric oil pump relay
• TCM
• Harness or connector
(Open circuit or short circuit
in harness between the TCM
and the electric oil pump.)
+
−
Condition
Voltage
Electric oil pump relay
Connector
Terminal
F119
1
Ground
Always
10 – 16 V
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст