Nissan Qashqai J11. Manual — part 916
PB-46
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING ELECTRIC PARKING BRAKE CON-
TROL MODULE
ADDITIONAL SERVICE WHEN REPLACING ELECTRIC PARKING BRAKE
CONTROL MODULE
Work Procedure
INFOID:0000000010833860
When replacing the electric parking brake control module be sure to perform the following procedure.
1.
CONFIGURATION
Perform the configuration. Refer to
.
>> GO TO 2.
2.
CALIBRATION OF G SENSOR
Perform the calibration of G sensor. Refer to
.
>> GO TO 3.
3.
RESET OF CLUTCH PEDAL STROKE SENSOR
Perform the reset of clutch stroke sensor. Refer to
>> GO TO 4.
4.
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
Perform the adjustment of rear brake caliper initial position: Refer to
>> GO TO 5.
5.
OPERATION OF REAR BRAKE CALIPER
Perform the operation of rear brake caliper: Refer to
>> GO TO 6.
6.
RELEASE OF REAR BRAKE CALIPER
Perform the release of rear brake caliper: Refer to
>> GO TO 7.
7.
CHANGE OF SYSTEM MODE
Perform the change of system mode: Refer to
>> End of work.
REPLACEMENT OF REAR BRAKE PAD
PB-47
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
REPLACEMENT OF REAR BRAKE PAD
Description
INFOID:0000000010833861
CAUTION:
When performing the following operations, always use CONSULT, for performing “START BRAKE PAD
REPLACEMENT”, “FINISH BRAKE PAD REPLACEMENT”, “INITIALIZATION POSITION ADJUSTMENT”,
“BRAKE OPERATION” and “BRAKE RELEASE” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833862
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Replacing rear brake caliper assembly
1.
BEFORE REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Never start the engine.
2.
Select “EHS/PKB”, “WORK SUPPORT”, and “START BRAKE PAD REPLACEMENT” according to this
order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
3.
Touch “START”.
>> GO TO 2.
2.
REMOVAL AND INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER
ASSEMBLY
Replace the rear brake pad or rear brake caliper.
Procedure
• START BRAKE PAD REPLACEMENT
• FINISH BRAKE PAD REPLACEMENT
• INITIALIZATION POSITION ADJUSTMENT
• BRAKE OPERATION
• BRAKE RELEASE
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
—
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
—
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
PB-48
< BASIC INSPECTION >
REPLACEMENT OF REAR BRAKE PAD
With CONSULT
Select “EHS/PKB”, “DATA MONITOR”, “BRAKE FORCE (LH)” and “BRAKE FORCE (RH)” according to this
order. Check that signals are within the specified value. Refer to
.
Is the check result normal?
YES
>> GO TO 9.
NO
>> GO TO 1.
9.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.
2.
Erase self-diagnosis results memory of “EHS/PKB”.
Is the memory erased?
YES
>> INSPECTION END
NO
>> Check the items indicated by the self-diagnosis.
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
PB-49
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
Description
INFOID:0000000010833863
CAUTION:
When performing the following operations, always use CONSULT, for performing “INITIALIZATION
POSITION ADJUSTMENT”, “BRAKE OPERATION” and “BRAKE RELEASE” of “WORK SUPPORT”.
×
: Required
—: not required
Work Procedure
INFOID:0000000010833864
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Replacing rear brake caliper assembly
1.
PERFORM INITIALIZATION POSITION ADJUSTMENT
With CONSULT
1.
Turn the ignition switch OFF to ON.
2.
Select “EHS/PKB”, “WORK SUPPORT”, and “INITIALIZATION POSITION ADJUSTMENT” according to
this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
3.
Touch “START”.
>> GO TO 2.
2.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
Procedure
• INITIALIZATION POSITION ADJUSTMENT
• BRAKE OPERATION
• BRAKE RELEASE
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
—
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
—
Replacing clutch stroke sensor
—
Removing/installing clutch pedal
—
Replacing clutch pedal
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст