Nissan Qashqai J11. Manual — part 899
BR-68
< REMOVAL AND INSTALLATION >
[RHD]
BRAKE MASTER CYLINDER
BRAKE MASTER CYLINDER
Exploded View
INFOID:0000000010305460
HRA2DDT - MR20DD
JPFIA0080GB
1.
Reservoir cap
2.
Reservoir tank
3.
Cylinder body
4.
Pin
5.
O-ring
6.
Grommet
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
: Apply brake fluid.
for symbols not described on the above.
BRAKE MASTER CYLINDER
BR-69
< REMOVAL AND INSTALLATION >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
K9K - R9M
Removal and Installation
INFOID:0000000010305461
REMOVAL
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
1.
Drain brake fluid. Refer to
2.
Disconnect the brake fluid level switch harness connector.
3.
Disconnect the brake tubes from the master cylinder assembly with a flare nut wrench.
CAUTION:
Never scratch the flare nut and the brake tube.
4.
Remove the master cylinder assembly.
CAUTION:
• Depress the brake pedal several times to release the vacuum pressure from the brake booster.
Then remove the master cylinder assembly.
• Never depress the brake pedal after the master cylinder assembly is removed.
• The piston of the master cylinder assembly is exposed. Never damage it when removing the
master cylinder.
• The piston may drop off when pulled out strongly. Never hold the piston. Hold the cylinder body
when handling the master cylinder assembly.
INSTALLATION
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
E1FIA0154GB
1.
Reservoir cap
2.
Reservoir tank
3.
Cylinder body
4.
Pin
5.
Grommet
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
: Apply brake fluid.
Refer to
for symbols not described on the above.
BR-70
< REMOVAL AND INSTALLATION >
[RHD]
BRAKE MASTER CYLINDER
• Note the following, and installation is the reverse order of removal.
CAUTION:
• Never depress the brake pedal after the master cylinder assembly is removed.
• Apply PBC (Poly Butyl Cuprysil) silicone-based grease to
the brake booster [see (A) in the figure] when installing the
master cylinder assembly to the brake booster.
• The piston of the master cylinder assembly is exposed.
Never damage it when handling the master cylinder and
check that no dirt and dust are present on the piston before
installation. Clean it with new brake fluid if necessary.
• The piston may drop off when pulled strongly. Never hold
the piston. Hold the cylinder body when handling the master
cylinder assembly.
• Temporarily tighten the brake tube flare nut to the master cylinder
assembly by hand. Then tighten it to the specified torque with a
flare nut torque wrench. Refer to
BR-63, "FRONT : Exploded View"
CAUTION:
Never scratch the flare nut and the brake tube.
• After installation, perform the air bleeding. Refer to
BR-56, "Bleeding Brake System"
.
CAUTION:
Never reuse drained brake fluid.
Disassembly and Assembly
INFOID:0000000010305462
DISASSEMBLY
CAUTION:
• Never disassemble the cylinder body.
• Remove the reservoir tank if necessary.
1.
Fix the master cylinder assembly to a vise.
CAUTION:
Always set copper plates or cloth between vise when fixing the cylinder body to a vise. Never
overtighten the vise.
2.
Remove the reservoir tank mounting pin with a pin punch.
3.
Remove the reservoir tank and grommet from the cylinder body.
CAUTION:
Never drop the removed parts. The parts must not be
reused if they are dropped.
ASSEMBLY
1.
Apply new brake fluid to the grommet and install it to the cylinder body.
CAUTION:
• Never use mineral oil such as gasoline or light oil.
• Never reuse the grommets.
2.
Install the reservoir tank to the cylinder body.
CAUTION:
• Never drop the parts when installing. The parts must not be reused if they are dropped.
• Never reuse reservoir tank.
JPFIA0013ZZ
JPFIA0015ZZ
BRAKE MASTER CYLINDER
BR-71
< REMOVAL AND INSTALLATION >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
3.
Fix the cylinder body to a vise.
CAUTION:
• Place the reservoir tank with the chamfered pin hole (
)
facing up.
• Always set copper plates or cloth between vise when fix-
ing the cylinder body to a vise. Never overtighten the vise.
4.
Tilt the reservoir tank so that a mounting pin can be inserted.
Insert a mounting pin. Return the reservoir tank to the horizontal
position. Insert another mounting pin into the pin hole on the
opposite side in the same manner after the mounting pin passes
through the cylinder body pin hole.
CAUTION:
Never reuse the mounting pin.
Inspection
INFOID:0000000010305463
INSPECTION AFTER INSTALLATION
Fluid Leak
Check for brake fluid leakage from the cylinder body-to-brake booster mounting face, reservoir tank mounting
face and brake tube connections.
JPFIA0016ZZ
JPFIA0015ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст