Nissan Qashqai J11. Manual — part 895
BR-52
< PERIODIC MAINTENANCE >
[RHD]
BRAKE PEDAL
PERIODIC MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment
INFOID:0000000010305434
INSPECTION
Brake Pedal Height
Check the height (H
1
) between the accelerator pedal stopper (1) and
the brake pedal upper surface.
CAUTION:
Remove the floor trim.
ASCD brake Switch and Stop Lamp Switch
Check the clearance (C) between bracket (1) and ASCD brake
switch/stop lamp switch (2) threaded end.
CAUTION:
The stop lamp must be turned off when the brake pedal is
released.
NOTE:
Pull the brake pedal pad to make the clearance between bracket and ASCD brake switch/stop lamp switch
threaded end.
Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A).
Depressed Brake Pedal Height
Standard
Brake pedal height (H
1
)
: Refer to
.
JPFIA0119ZZ
Standard
Clearance (C) between
bracket and ASCD brake
switch/stop lamp switch
threaded end
: Refer to
.
JPFIA0206ZZ
Standard
Pedal play (A)
: Refer to
.
JPFIA0121ZZ
BRAKE PEDAL
BR-53
< PERIODIC MAINTENANCE >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Check the height between the accelerator pedal stopper (1) and the
brake pedal upper surface (H
2
) when depressing the brake pedal at
490 N (50 kg, 110 lb) while turning engine ON.
CAUTION:
Remove the floor trim.
ADJUSTMENT
Brake Pedal Height
1.
Disconnect the harness connector from ASCD brake switch and stop lamp switch.
2.
Turn the ASCD brake switch and stop lamp switch 45
°
counterclockwise.
3.
Loosen the input rod lock nut (1). Adjust the brake pedal to the
specification. Tighten the input rod lock nut to the specification.
Refer to
.
CAUTION:
The threaded end of the input rod (2) must project to the
inner side (L) of the clevis (3).
ASCD brake Switch and Stop Lamp Switch
1.
Disconnect the harness connector from ASCD brake switch and stop lamp switch.
2.
Turn the ASCD brake switch and stop lamp switch 45
°
counterclockwise.
3.
Press-fit ASCD brake switch/stop lamp switch (2) until ASCD
brake switch/stop lamp switch hits the bracket (1) 45
°
clockwise.
CAUTION:
• The clearance (C) between the bracket and ASCD brake
switch/stop lamp switch threaded end must be the speci-
fied value. Refer to
.
• The stop lamp must be turned off when the brake pedal is
released.
Brake Pedal Play
1.
Disconnect the harness connector from ASCD brake switch and stop lamp switch.
2.
Turn the ASCD brake switch and stop lamp switch 45
°
counterclockwise.
Standard
Depressed brake pedal
height (H
2
)
: Refer to
JPFIA0120ZZ
JPFIA0003ZZ
Standard
Brake pedal height (H
1
)
: Refer to
JPFIA0119ZZ
JPFIA0206ZZ
BR-54
< PERIODIC MAINTENANCE >
[RHD]
BRAKE PEDAL
3.
Press-fit ASCD brake switch/stop lamp switch (2) until ASCD
brake switch/stop lamp switch hits the bracket (1) 45
°
clockwise.
CAUTION:
• The clearance (C) between the bracket and ASCD brake
switch/stop lamp switch threaded end must be the speci-
fied value. Refer to
.
• The stop lamp must be turned off when the brake pedal is
released.
JPFIA0206ZZ
BRAKE FLUID
BR-55
< PERIODIC MAINTENANCE >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE FLUID
Inspection
INFOID:0000000010305435
BRAKE FLUID LEVEL
• Check that the fluid level in the reservoir tank is within the specified
range (MAX – MIN lines).
• Visually check for any brake fluid leakage around the reservoir
tank.
• Check the brake system for any leakage if the fluid level is
extremely low (lower than MIN).
• Check the brake system for fluid leakage if the warning lamp
remains illuminated even after the parking brake is released.
BRAKE LINE
1.
Check brake line (tubes and hoses) for cracks, deterioration or other damage. Replace any damaged
parts.
2.
Check for fluid leakage by fully depressing brake pedal while
engine is running.
CAUTION:
If leakage occurs around joints, retighten or, if necessary,
replace damaged parts.
Draining
INFOID:0000000010305436
CAUTION:
• Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
• Turn the ignition switch OFF and disconnect the ABS actuator and electric unit (control unit) con-
nector or the battery negative terminal before draining.
1.
Connect a vinyl tube to the bleed valve.
2.
Depress the brake pedal and loosen the bleeder valve to gradu-
ally discharge brake fluid.
Refilling
INFOID:0000000010305437
CAUTION:
Turn the ignition switch OFF and disconnect the ABS actuator and electric unit (control unit) connec-
tor or the battery negative terminal before refilling.
JPFIA0007ZZ
SBR389C
BRA0007D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст