Nissan Qashqai J11. Manual — part 1403
BACK DOOR OPENER ACTUATOR
DLK-881
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection normal?
YES
>> Replace back door lock assembly.
NO
>> Repair or replace harness.
Back door lock assembly
Ground
Continuity
Connector
Terminal
B2
2
Existed
DLK-882
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
BACK DOOR OPENER SWITCH
BACK DOOR OPENER SWITCH
Component Function Check
INFOID:0000000010672500
1.
CHECK FUNCTION
1.
Select “TRUNK” of “BCM” using CONSULT.
2.
Select “BACK DOOR OPENER SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Back door opener switch is OK.
NO
>> Refer to
DLK-882, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010672501
1.
CHECK BACK DOOR OPENER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check signal between back door opener switch assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door opener switch assembly harness con-
nector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT
Check continuity between back door opener switch assembly harness connector and ground.
Monitor item
Condition
Status
BACK DOOR OPENER SW
Back door opener switch
Pressed
ON
Released
OFF
(+)
(–)
Voltage
Back door opener switch assembly
Connector
Terminal
D94
1
Ground
9 - 16 V
BCM
Back door opener switch assembly
Continuity
Connector
Terminal
Connector
Terminal
B4
16
D94
1
Existed
BCM
Ground
Continuity
Connector
Terminal
B4
16
Not existed
BACK DOOR OPENER SWITCH
DLK-883
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR OPENER SWITCH
DLK-883, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door opener switch assembly.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010672502
1.
CHECK BACK DOOR OPENER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door opener switch assembly connector.
3.
Check continuity between back door opener switch assembly terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace back door opener switch assembly.
Back door opener switch assembly
Ground
Continuity
Connector
Terminal
D94
4
Existed
Back door opener switch assembly
Condition
Continuity
Terminal
1
4
Back door opener
switch
Pressed
Existed
Released
Not existed
DLK-884
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 6]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010672503
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-884, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010672504
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
LHD models
RHD models
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
LHD models
Monitor item
Status
DOOR LOCK
ALL LOCK
Door lock actuators
LOCK
ALL UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D1
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D25
2
Ground
Door lock and unlock switch
Unlock
9 – 16 V
3
Lock
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
141
D1
3
Existed
148
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст