Nissan Qashqai J11. Manual — part 1386
HOOD LOCK
DLK-813
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• After installation, perform hood fitting adjustment. Refer to
DLK-784, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD SAFETY HOOK
HOOD SAFETY HOOK : Removal and Installation
INFOID:0000000010678820
REMOVAL
Remove mounting nuts, and then remove hood lock secondary assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000010678821
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch is securely engaged with secondary striker from the dead load of the hood
assembly.
3.
Check that primary latch is securely engaged with primary striker when hood assembly is closed [free-fall
from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
4.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
5.
Check that secondary latch is properly engaged with secondary striker [4.0 mm (0.157 in)].
6.
Check the hood lock lubrication condition. If necessary, apply
body grease to hood lock assembly.
PIIB5801E
: Body grease
JMKIB1164ZZ
DLK-814
< REMOVAL AND INSTALLATION >
[TYPE 5]
FRONT DOOR LOCK
FRONT DOOR LOCK
Exploded View
INFOID:0000000010678822
*
1
: Driver side only
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010678823
REMOVAL
1.
Disconnect inside handle cable from inside handle. Refer to
DLK-815, "INSIDE HANDLE : Removal and
.
2.
Disconnect outside handle cable from outside handle bracket. Refer to
.
3.
Disconnect door lock assembly harness connector.
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Key rod*
1
6.
Door lock assembly
7.
cable clip
8.
Inside handle
9.
Front gasket
10. Outside handle grip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIB3253GB
FRONT DOOR LOCK
DLK-815
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4.
Remove door lock assembly screws, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse door lock assembly screw. Always replace it with a new one when it is removed.
• Check door lock cable is properly engaged with outside handle bracket.
• When installing key rod, rotate key rod holder until a click is felt.
• Check door lock assembly for poor lubrication. Refer to
DLK-815, "DOOR LOCK : Inspection"
• Check door open/close, lock/unlock operation after installation.
DOOR LOCK : Inspection
INFOID:0000000010678824
Check door lock assembly for poor lubrication. Apply body grease if
necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000010678825
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting bolt.
3.
Disengage inside handle from door panel while sliding inside handle toward vehicle rear, and then sepa-
rate inside handle.
4.
Disconnect inside handle cable, and then remove inside handle.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010678826
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove front door glass rear run. Refer to
GW-23, "Removal and Installation"
.
5.
Disengage outside handle cable from cable clip.
6.
Disengage rod holder, and then disconnect key rod from door lock assembly. (Driver side only)
7.
Disconnect outside handle harness connector.
: Body grease
JMKIA8534ZZ
DLK-816
< REMOVAL AND INSTALLATION >
[TYPE 5]
FRONT DOOR LOCK
8.
Remove grommet (1) of door side. Loosen, through grommet hole, TORX bolt (2) that fixes outside handle
escutcheon.
9.
While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, remove outside
handle escutcheon (2).
10. While pulling outside handle (1) according to the numerical order
1
→
2 indicated by arrows as shown in the figure, slide toward
rear of vehicle to remove outside handle.
11. Remove front gasket (1) and rear gasket (2).
JMKIB2462ZZ
JMKIA8374ZZ
JMKIA0524ZZ
: Pawl
: Vehicle front
JMKIB1627ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст