Nissan Qashqai J11. Manual — part 1173
HEADLINING
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
13. Remove headlining assembly through the back door.
CAUTION:
• Two workers are required for removal in order to prevent damage.
• Apply protective tape to the portion where contact may occur during work.
• Never bend headlining when removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.
• When finstalling assist grip, install metal clip (1) to assist grip
cap (2) and then instal to the body panel.
JMJIA9641ZZ
JMJIA3623ZZ
INT-28
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
LUGGAGE TRIM
Exploded View
INFOID:0000000010350947
1.
Lamp assembly
2.
Rear pillar finisher
3.
Parcel shelf
4.
Luggage floor carpet
5.
Luggage floor spacer (RH)
6.
Luggage floor spacer(LH)
7.
Luggage floor board assembly
8.
Luggage floor board assembly
9.
Luggage floor carpet
E1JIA0281GB
LUGGAGE TRIM
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Luggage side trim
INFOID:0000000010350948
REMOVAL
LUGGAGE SIDE LOWER FINISHER (FRONT)
1.
Remove rear kicking plate inner. Refer to
INT-18, "Removal and Installation"
.
2.
Release luggage side lower finisher (front) portion from rear body side welt.
3.
Remove rear seat cushion assembly and rear seatback assembly. Refer to
4.
Disengage luggage side lower finisher (front) fixing clips.
5.
Remove luggage side lower finisher (front).
LUGGAGE SIDE LOWER FINISHER
CAUTION:
Be careful not to damage the body panel.
1.
Fully open back door.
2.
Remove back door weather-strip. Refer to
DLK-356, "BACK DOOR WEATHER-STRIP : Removal and
.
3.
Remove luggage rear plate fixing clips.
4.
Disengage luggage rear plate fixing pawls and metal clips.
5.
Remove luggage rear plate.
6.
Remove rear parcel shelf finisher (if equipped).
7.
Remove luggage floor carpet.
8.
Remove luggage floor board (if equipped).
9.
Remove luggage side lower finisher (front).
10. Remove rear pillar finisher. Refer to
INT-18, "Removal and Installation"
11. Remove trunk side finisher mounting bolts.
12. Remove trunk side finisher.
13. Remove luggage floor carpet front fixing clips.
14. Remove luggage floor carpet front.
15. Remove luggage side lower finisher fixing clips.
16. Remove luggage side lower finisher.
10. Luggage floor spacer (RH)
11. Luggage floor spacer (LH)
12. Front luggage floor carpet structure
13. Back door trim finisher upper
14. Hook assembly
15. Rear body assembly
16. Hook rope (LH)Rear center luggage
floor spacer assembly (if equipped)
17. Luggage side lower finisher
18. Front luggage side lower finisher
19. Back door assembly
20. Luggage rear plate
21. Back door trim finisher lower
22. Back door pull handle
A
With luggage floor spacer
B
Without luggage floor spacer
C
Without luggage floor spacer and
luggage floor board assembly
: Clip
: Pawl
: Metal clip
JMJIA0245ZZ
INT-30
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
REAR PILLAR FINISHER
CAUTION:
Be careful not to damage the body panel.
1.
Remove rear seat cushion and rear seatback assembly. Refer to
SE-35, "Removal and Installation"
2.
Remove lower anchor bolt. Refer to
3.
Disengage seat belt finisher fixing pawls, and then remove seat belt finisher.
4.
Remove luggage side lower finisher (front). Refer to
5.
Remove luggage room lamp (rear pillar finisher LH side only). Refer to
INL-79, "Removal and Installation"
.
6.
Release rear pillar finisher portion of back door weather-strip.
7.
Disengage rear pillar finisher fixing clips and metal clips.
8.
Remove rear pillar finisher (LH/RH).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Visually check clips and metal clips for deformation and damage during installation. Replace with new
one if necessary.
When installing check in advance that clips and metal clips are accurately aligned with the portions on
body panel.
Luggage floor trim
INFOID:0000000010375508
REMOVAL
LUGGAGE REAR PLATE
1.
Remove luggage floor carpet and luggage floor spacers.
2.
Remove back door weather-strip. Refer to
INT-31, "Removal and Installation"
3.
Insert remover tool (A) between luggage rear plate and luggage
rear plate cap (1) to disengage pawls and then remove luggage
rear plate cap.
4.
Remove both clips (B) on luggage rear plate using a remover
tool (A).
5.
Hold both sides of rear plate, pull upwards to remove.
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMJIA0235ZZ
JMJIA0236ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст