Nissan Qashqai J11. Manual — part 2124
AV
INSPECTION AND ADJUSTMENT
AV-185
< BASIC INSPECTION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
1.
On the CONSULT screen, touch “CALIBRATING CAMERA IMAGE (FRONT CAMERA)”, “CALIBRATING
CAMERA IMAGE (PASS-SIDE CAMERA)”, “CALIBRATING CAMERA IMAGE (DR-SIDE CAMERA)”, or
“CALIBRATING CAMERA IMAGE (REAR CAMERA)” to accept the selection.
NOTE:
To cancel the indication of Incomplete calibration, select items based on the target camera.
2.
On the adjustment screen of each camera, adjust the parameter
by touching the “AXIS X” button, “AXIS Y” button, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
3.
Touch “APPLY” button on the CONSULT screen. “PRCSNG” is
displayed and adjustment results are shown on the camera screen.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
4.
Touch “OK” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
>> GO TO 6.
6.
PERFORM “FINE TUNING OF BIRDS-EYE VIEW”
This mode is designed to align the boundary between each camera image that could not be aligned in the
“Calibrating Camera Image” mode.
CONSULT work support
1.
Select “FINE TUNING OF BIRDS-EYE VIEW” by touching CONSULT screen.
2.
On the adjustment screen of each camera, adjust the parameter
by touching the “AXIS X” button, “AXIS Y” button”, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
NOTE:
Touch “SELECT” button on the CONSULT screen to select the
target camera.
3.
Touch “APPLY” button on the CONSULT screen. “PRCSNG” is
displayed and adjustment results are shown on the camera
screen.
CAUTION:
Check that “PRCSNG” is displayed. Never perform other
operations while “PRCSNG” is displayed.
4.
Touch “OK” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
• Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
• After pressing the “OK” button, never press buttons other than the “BACK” button.
NOTE:
• It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration”.
• The adjustment value is cancelled in this mode by performing “Initialize Camera Image Calibration”.
>> Calibration End.
Adjustment range
Rotation direction (Center dial)
: 31 patterns (16 on the center)
Upper/lower direction (upper/lower
switch)
:
−
22 – 22
Left/right direction (left/right switch)
:
−
22 – 22
JSNIA4212ZZ
JSNIA4214ZZ
AV-186
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C1A00 CONTROL UNIT
DTC/CIRCUIT DIAGNOSIS
C1A00 CONTROL UNIT
DTC Logic
INFOID:0000000010944751
DTC DETECTION LOGIC
POSSIBLE CAUSE
Around view monitor control unit
FAIL-SAFE
Around view monitor with Park Assist is cancel
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT
1.
Turn ignition switch ON.
2.
Perform “All DTC Reading” with CONSULT.
3.
Check if the “C1A00” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “C1A00” detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010944752
1.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
Check if any DTC other than “C1A00” is detected in “Self Diagnostic Result” of “AVM”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
AV-154, "WITHOUT DRIVER ASSISTANCE SYSTEM : DTC Index"
.
NO
>> Replace around view monitor control unit. Refer to
AV-267, "Removal and Installation"
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
C1A00
AVM CIRC
(Around view monitor circuit)
Around view monitor control unit malfunction is detected
AV
C1B56 SONAR
AV-187
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
C1B56 SONAR
DTC Logic
INFOID:0000000010944764
DTC DETECTION LOGIC
POSSIBLE CAUSE
Sonar control unit
FAIL-SAFE
Around view monitor with Park Assist is cancel
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
WITH CONSULT.
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the “C1B56” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
“C1B56” detected as the current malfunction?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010944765
1.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT.
Check if the “U1000” is detected other than “C1B56” in “Self Diagnostic Result” of “AVM”.
“U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
AV-189, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
.
NO
>> GO TO 2.
2.
CHECK SELF-DIAGNOSIS RESULTS
With CONSULT.
Check if any DTC is detected in “Self Diagnostic Result” of “SONAR”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> Replace the around view monitor control unit. Refer to
AV-267, "Removal and Installation"
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
C1B56
SONAR CIRC
(Sonar circuit)
The around view monitor control unit detects that sonar control unit has a mal-
function.
AV-188
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION]
U0428 STEERING ANGLE SENSOR
U0428 STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000010435682
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000010435683
1.
ADJUST THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
When U0428 is detected, adjust the neutral position of the steering angle sensor.
>> Perform adjustment of the neutral position of the steering angle sensor. Refer to
OUT DRIVER ASSISTANCE SYSTEM : CONSULT Function"
CONSULT Display
DTC Detection Condition
Possible Cause
ST ANG SEN CALIB
[U0428]
The neutral position adjustment of the steering
angle sensor is incomplete.
Adjust neutral position of the steering angle sen-
sor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст