Nissan Qashqai J11. Manual — part 695
P0967 PRESSURE CONTROL SOLENOID B
TM-355
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
NO
>> There is malfunction of primary pressure solenoid valve. Replace transaxle assembly. Refer to
TM-356
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P2765 INPUT SPEED SENSOR B
P2765 INPUT SPEED SENSOR B
DTC Logic
INFOID:0000000010589349
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P2765
INPUT SPEED SENSOR B
(Input/Turbine Speed Sensor
B Circuit)
When 1 is satisfied and any of 2, 3 or 4 is sat-
isfied and this state is maintained for 5 sec-
onds:
1.
When all of the following conditions are
satisfied:
-
TCM power supply voltage: More than 11
V
-
After range change completion, it spends
2 seconds or more.
2.
When all of the following conditions are
satisfied and this state is maintained for
5 seconds:
-
Secondary pulley speed: Less than 149
rpm
-
Primary pulley speed: 1,000 rpm or more
3.
When all of the following conditions are
satisfied and this state is maintained for
0.5 seconds:
-
10-msec-ago secondary pulley speed:
1000 rpm or more
-
Now secondary pulley speed: 0 rpm
4.
When all of the following conditions are
satisfied and this state is maintained for
5 seconds:
-
Range: D
-
Engine speed: 450 rpm or more
-
Primary pulley speed: 300 rpm or more
-
Secondary pulley speed: 300 rpm or
more
-
Input speed: 300 rpm or more
-
The difference between engine speed
and primary pulley speed is 1,000 rpm or
less
-
The difference between engine speed
and input speed is 1,000 rpm or less
-
The difference between primary pulley
speed and input speed is 1,000 rpm or
less
-
Lock-up command is being given (except
for slip lock-up)
-
DTC other than the applicable DTC is not
detected.
-
When any of following items are satis-
fied:
•
Primary pulley speed/secondary pulley
speed: More than 2.9
•
Primary pulley speed/secondary pulley
speed: Less than 0.3
• Harness or connector
(Output speed sensor circuit is open or
shorted)
• Output speed sensor
P2765 INPUT SPEED SENSOR B
TM-357
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
>> GO TO 2.
2.
CHECK DTC DETECTION
1.
Start the engine.
2.
Drive the vehicle.
3.
Maintain the following conditions for 10 seconds or more.
4.
Stop the vehicle.
5.
Check the first trip DTC.
Is “P2765” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010589350
1.
CHECK OUTPUT SPEED SENSOR POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect output speed sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between output speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 6.
2.
CHECK OUTPUT SPEED SENSOR GROUND CIRCUIT
Check continuity between output speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between output speed sensor harness connector terminal and TCM harness connector
terminal.
Is the inspection result normal?
Selector lever
: “D” position
Engine speed
: 1,200 rpm or more
Vehicle speed
: 55 km/h (34 MPH) or more
+
−
Voltage
Output speed sensor
Connector
Terminal
F41
3
Ground
10 – 16 V
Output speed sensor
—
Continuity
Connector
Terminal
F41
1
Ground
Existed
Output speed sensor
TCM
Continuity
Connector
Terminal
Connector
Terminal
F41
2
F2
34
Existed
TM-358
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P2765 INPUT SPEED SENSOR B
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK CIRCUIT BETWEEN OUTPUT SPEED SENSOR AND TCM (PART 2)
Check continuity between output speed sensor harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK TCM INPUT SIGNALS
1.
Connect all of disconnected connectors.
2.
Lift the vehicle.
3.
Start the engine.
4.
Check frequency of output speed sensor.
Is the inspection result normal?
YES >> Check
intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace output speed sensor. Refer to
TM-401, "Removal and Installation"
.
6.
CHECK CIRCUIT BETWEEN IPDM E/R AND OUTPUT SPEED SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector terminal and output speed sensor harness con-
nector terminals.
Is the check result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
DETECT MALFUNCTIONING ITEMS
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to
gram - IGNITION POWER SUPPLY -"
• Short circuit in harness between IPDM E/R harness connector terminal 100 and output speed sensor har-
ness connector terminal 3.
• 10A fuse (No.63, located in the IPDM E/R). Refer to
PG-101, "Fuse, Connector and Terminal Arrangement"
.
• IPDM E/R
Output speed sensor
—
Continuity
Connector
Terminal
F41
2
Ground
Not existed
+
−
Condition
Frequency
(Approx.)
TCM
Connector
Terminal
F2
34
Ground
• Shift position: “M1” position
• Vehicle speed: 20 km/h (12 MPH)
200 Hz
JSDIA1904GB
IPDM E/R
Output speed sensor
Continuity
Connector
Terminal
Connector
Terminal
F90
100
F41
3
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст