Nissan Qashqai J11. Manual — part 1754
EXL-318
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
Removal and Installation
INFOID:0000000010437125
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Remove front bumper fascia. Refer to
EXT-19, "Removal and Installation"
.
2.
Remove front combination lamp assembly mounting bolts.
3.
Pull out front combination lamp assembly forward the vehicle.
4.
Disconnect front combination lamp assembly harness connectors.
5.
Remove front combination lamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to the following:
• LHD MODELS: Refer to
.
Front combination lamp housing
Seal packing
Headlamp bulb (LO)
Headlamp aiming motor
Headlamp socket cover assembly
Front combination lamp bracket
Front turn signal lamp bulb socket
Headlamp bulb (HI)
Front turn signal lamp bulb
JMLIA5091ZZ
FRONT COMBINATION LAMP
EXL-319
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• RHD MODELS: Refer to
Replacement
INFOID:0000000010437127
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
.
• After installing the bulb, install the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (HI)
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EM-279, "Removal and Installation"
• R9M: Refer to
EM-380, "Removal and Installation"
2.
Disconnect headlamp bulb (HI) harness connector.
3.
Rotate headlamp socket cover assembly counterclockwise and unlock it.
4.
Remove headlamp socket cover assembly from head lamp bulb (HI).
5.
Remove retaining spring lock, and then remove headlamp bulb (HI) from front combination lamp housing.
RH side
1.
Disconnect headlamp bulb (HI) harness connector.
2.
Rotate headlamp socket cover assembly counterclockwise and unlock it.
3.
Remove headlamp socket cover assembly from headlamp bulb (HI).
4.
Remove retaining spring lock, and then remove headlamp bulb (HI) from front combination lamp housing.
HEADLAMP BULB (LO)
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EM-279, "Removal and Installation"
• R9M: Refer to
EM-380, "Removal and Installation"
2.
Disconnect headlamp bulb (LO) harness connector.
3.
Rotate headlamp bulb socket (LO) counterclockwise and unlock it.
4.
Remove headlamp bulb (LO) from front combination lamp housing.
RH side
1.
Disconnect headlamp bulb (LO) harness connector.
2.
Rotate headlamp bulb socket (LO) counterclockwise and unlock it.
3.
Remove headlamp bulb (LO) from front combination lamp housing.
DAYTIME RUNNING LIGHT/ PARKING LAMP BULB
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. for replacement, replace
front combination lamp as a set.
FRONT TURN SIGNAL LAMP BULB
LH side
1.
Remove air duct. Refer to the following.
• HRA2DDT: Refer to
EM-23, "Removal and Installation"
EM-147, "Removal and Installation"
• K9K: Refer to
EXL-320
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
• R9M: Refer to
EM-380, "Removal and Installation"
2.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
3.
Remove front turn signal lamp bulb socket from front combination lamp housing.
4.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
RH SIDE
1.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
2.
Remove front turn signal lamp bulb socket from front combination lamp housing.
3.
Remove front turn signal lamp bulb from turn signal lamp bulb socket.
Disassembly and Assembly
INFOID:0000000010437128
DISASSEMBLY
1.
Remove headlamp bracket mounting screws, and then remove headlamp bracket from front combination
lamp housing.
2.
Disconnect front combination lamp harness connectors.
3.
Rotate head lamp socket cover assembly counterclockwise and unlock it.
4.
Remove head lamp socket cover assembly from halogen lamp bulb (HI).
5.
Remove retaining spring lock, and then remove halogen lamp bulb (HI) from front combination lamp hous-
ing.
6.
Rotate halogen lamp bulb (LO) counterclockwise and unlock it.
7.
Remove halogen lamp bulb (LO) from front combination lamp housing.
8.
Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
9.
Remove front turn signal lamp bulb socket from front combination lamp housing.
10. Remove front turn signal lamp bulb from front turn signal lamp bulb socket.
11. Remove head lamp aiming motor from front combination lamp housing.
ASSEMBLY
Note the following item, and then install in the reverse order of removal.
CAUTION:
• After installing the bulb, install the bulb socket securely watertightness.
• After installation, perform aiming adjustment. Refer to the following.
- LHD models: Refer to
.
- RHD models: Refer to
FRONT FOG LAMP
EXL-321
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000010437133
Removal and Installation
INFOID:0000000010437134
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-182, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Remove front fender protector to make work space. Refer to
EXT-32, "Removal and Installation"
2.
Disconnect front fog lamp harness connector.
3.
Remove front fog lamp fixing bolt, and then remove front fog lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000010437135
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
Front bumper fascia
Front bumper finisher
Front fog lamp
Front fog lamp bulb
: N·m (kg-m, in-lb)
JMLIA5093GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст