Nissan Qashqai J11. Manual — part 1851
BCS-130
< SYMPTOM DIAGNOSIS >
COMBINATION SWITCH SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000010378041
1.
Perform “Data Monitor” of CONSULT to check for any malfunctioning item.
2.
Check the malfunction combinations.
Malfunction item:
×
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Data monitor item
Malfunc-
tion com-
bination
FR WIPE
R HI
F
R
WIPER LOW
FR W
ASHER S
W
FR
W
IP
E
R
I
N
T
WIP VOLUME
RR WIPER ON
R
R
WIPER
IN
T
RR W
ASHER SW
TURN SIGNAL R
T
U
R
N
SIGNAL L
T
A
IL LAM
P
SW
HI BEAM
SW
HE
A
D
LA
MP
S
W
LIGHT OFF
SW
P
ASSING SW
AUT
O
LI
GHT
SW
FR FOG SW
RR FOG SW
×
×
×
A
×
×
×
×
B
×
×
×
×
C
×
×
×
×
D
×
×
×
×
E
×
×
×
×
F
×
×
×
×
G
×
×
×
×
H
×
×
×
×
I
×
×
×
J
All Items
K
If only one item is detected or the item is not applicable to the combinations A to K
L
All Items are normal
M
Malfunction
combination
Malfunctioning part
Repair or replace
A
Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to
BCS-128, "Diagnosis Procedure"
.
B
Combination switch OUTPUT 2 circuit
C
Combination switch OUTPUT 3 circuit
D
Combination switch OUTPUT 4 circuit
E
Combination switch OUTPUT 5 circuit
F
Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to
BCS-126, "Diagnosis Procedure"
G
Combination switch INPUT 2 circuit
H
Combination switch INPUT 3 circuit
I
Combination switch INPUT 4 circuit
J
Combination switch INPUT 5 circuit
K
BCM
Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
L
Combination switch
Replace combination switch. Refer to
BCS-133, "Removal and Installation"
M
Connector and harness
Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
BCS
NORMAL OPERATING CONDITION
BCS-131
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
NORMAL OPERATING CONDITION
Description
INFOID:0000000010378042
SHIPPING MODE
• Shipping mode inhibits battery power consumption during transportation or storage of the vehicle. Vehicle is
set to shipping mode before being shipped from the factory.
• When ignition switch is OFF, BCM operates shipping mode.
• BCM control function is limited in shipping mode. Remote keyless entry function is not operated during the
shipping mode.
• For shipping mode cancel operation, refer to
.
NOTE:
Do not cancel shipping mode during storage of the vehicle. Always cancel shipping mode before delivery of
the vehicle to customer.
BCS-132
< REMOVAL AND INSTALLATION >
BCM
REMOVAL AND INSTALLATION
BCM
Removal and Installation
INFOID:0000000010378043
NOTE:
Before replacing BCM, perform “Before Replace ECU” of “Read / Write Configuration” to save or print current
vehicle specification. Refer to
REMOVAL (LHD MODELS)
1.
Disconnect the battery cable from the negative terminal.
2.
Remove the instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
.
3.
Remove the BCM mounting nut
, then pull out the BCM
.
4.
Disconnect the harness connectors from the BCM and remove.
REMOVAL (RHD MODELS)
1.
Disconnect the battery cable from the negative terminal.
2.
Remove the glove box assembly and glove box housing, Refer to
IP-13, "Removal and Installation"
.
3.
Disconnect the harness connectors from the BCM
.
4.
Remove the BCM mounting nuts
.
5.
Remove the BCM.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform “After Replace ECU” of “Read / Write Configuration” or “Manual Configuration”
when replacing BCM. Refer to
.
NOTE:
• Be sure to perform the system initialization (CAN gateway) when replacing BCM.
• Be sure to perform the system initialization (NATS) when replacing BCM.
• Be sure to perform the system initialization (TPMS) when replacing BCM.
ALMIA0690ZZ
JMMIA1655ZZ
BCS
COMBINATION SWITCH
BCS-133
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH
Removal and Installation
INFOID:0000000010378044
REMOVAL
1.
Remove steering column cover. Refer to
SR-17, "Removal and Installation"
.
2.
Remove screws
and disconnect connector
then pull up
combination switch
to remove it.
INSTALLATION
Install in the reverse order of removal.
JMMIA1168ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст