Nissan Qashqai J11. Manual — part 1338
REAR DOOR
DLK-621
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Fitting Adjustment Standard
Check the clearance and surface height between rear door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm [in]
Fitting Adjustment Procedure
1.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. Refer to
DLK-617, "DOOR HINGE : Inspec-
8.
Install center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010479428
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse mounting TORX bolt. Always replace it with a new one when it is removed.
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010479429
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
: N·m (kg-m, ft-lb)
: Body grease
Portion
Standard
Front door – Rear door
B – B
J
Clearance
3.3 – 5.3
[0.130 – 0.209]
K
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
Rear door – Body side panel
C – C
L
Clearance
3.5 – 5.5
[0.138 – 0.217]
M
Surface
height
(
−
1.0) – (+1.0)
[(
−
0.039) – (+0.039)]
DLK-622
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Remove rear door assembly. Refer to
DLK-619, "DOOR ASSEMBLY : Removal and Installation"
2.
Remove door hinge mounting bolts of vehicle body side, and then remove door hinge (lower).
3.
Remove center pillar lower garnish. Refer to
INT-18, "Removal and Installation"
.
4.
Remove door hinge mounting nuts of vehicle body side, and then remove door hinge (upper).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-615, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
• After installation, check door hinge rotating part for poor lubrication. Refer to
DOOR HINGE : Inspection
INFOID:0000000010479430
Check door hinge rotating part for poor lubrication. Apply body grease if necessary.
• Door hinge (upper)
• Door hinge (lower)
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010479431
REMOVAL
1.
Fully close the rear door glass.
2.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Removal and Installation"
.
3.
Remove rear door speaker.
a.
Disconnect rear door speaker harness connector.
b.
Remove rear door speaker mounting bolts, and then remove rear door speaker.
4.
Remove check link mounting bolts of vehicle body side.
: Body grease
JMKIB0329ZZ
: Body grease
JMKIB0321ZZ
REAR DOOR
DLK-623
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove check link mounting bolts of door side.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• After installation, check door check link rotating part for poor lubrication. Refer to
DOOR CHECK LINK : Inspection
INFOID:0000000010479432
Check door hinge rotating part for poor lubrication. Apply body
grease if necessary.
: Body grease
JMKIB0322ZZ
DLK-624
< REMOVAL AND INSTALLATION >
[TYPE 4]
BACK DOOR
BACK DOOR
Exploded View
INFOID:0000000010479433
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010479434
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
1.
Back door hinge
2.
Stud ball
3.
Back door stay
4.
Back door weather-strip
5.
Stud ball
6.
Back door bumper rubber
7.
Back door striker
8.
TORX bolt
9.
Back door panel
A.
Center mark
B.
Seam
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3637GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст