Nissan Qashqai J11. Manual — part 2210
DAS-254
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BA2-00 STEERING ANGLE SENSOR
NO
>> INSPECTION END
DAS
C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM
DAS-255
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM
DTC Description
INFOID:0000000010416999
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis Control Module
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BA5-00” detected?
YES
>> Proceed to
DAS-255, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417000
1.
CHECK ECM SYSTEM
With CONSULT
Perform self-diagnosis for “ECM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(HRA2DDT),
(K9K) or
(R9M).
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1BA5-00”, “U1000-00” or other DTC detected?
YES (“C1BA5-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA5-00
ADAS/CHASSIS CTRL ENGINE
SYS
(ADAS/Chassis control engine
system)
• When receiving from ECM that the value of the engine system signal transmitted
from the chassis control module to ECM is malfunctioning.
DAS-256
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BAB-00 STOP LAMP SWITCH
C1BAB-00 STOP LAMP SWITCH
DTC Description
INFOID:0000000010417001
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Stop lamp switch
• BCM
• Chassis Control Module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1BAB-00” detected?
YES
>> Proceed to
DAS-256, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010417002
1.
CHECK STOP LAMP SWITCH SYSTEM
With CONSULT
Perform self-diagnosis for “BCM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1BAB-00”, “U1000-00” or other DTC detected?
YES (“C1BAB-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BAB-00
STOP LAMP SW
(Stop lamp switch)
When a malfunction is detected in stop lamp switch system.
DAS
C1BAB-00 STOP LAMP SWITCH
DAS-257
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст