Nissan Qashqai J11. Manual — part 2022
MWI-24
< SYSTEM DESCRIPTION >
SYSTEM (METER SYSTEM)
• When all the following operating conditions are satisfied, the combination meter displays a tire warning on
the information display by an interrupt.
• The combination meter judges showing/hiding of “tire warning”, according to the signals below:
Other (Maintenance)
• When all the following operating conditions are satisfied, the combination meter displays a other warning on
the information display by an interrupt.
• The combination meter judges showing/hiding of “other warning”, according to the signals below:
Meter Illumination Control Indication
The level of brightness is displayed by operating the illumination control switch on the meter.
SETTING
Warning indication timing, unit, language, and time can be set.
Clock
This function is used for adjusting the clock and switching the clock display between Show and Hide, in addi-
tion to the display method between 12 hours and 24 hours.
Units
Setting values for unit items can be adjusted to meet the user's needs.
Operating condition
Ignition switch
ON
Mileage
More than value set in “SETTING”
Signal name
Signal path
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Operating condition
Ignition switch
ON
Mileage
More than value set in “SETTING”
Signal name
Signal path
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Setting item
Setting range
Clock
Set clock
24 Hr
0:00 - 23:59
12 Hr
0:00 - 11:59
24/12 Hr
24 Hr
—
12 Hr
—
Clock ON/OFF
ON
—
OFF
—
MWI
SYSTEM (METER SYSTEM)
MWI-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Maintenance
Setting values for service, tire, and other maintenance items can be adjusted to meet the user's needs.
Alert
Setting values for travel time, and low ambient temperature can be adjusted to meet the user's needs.
Language
Setting values for language items can be adjusted to meet the user's needs.
Factory
Settings can be reset.
Settings-reject Indication
• Regarding settings-reject indications, “SETTING CAN BE OPERATED WHEN STOPPED” is shown on the
information display when indication conditions are satisfied.
• When reaching 5 km/h (3.1 MPH) after accelerating from a stopping condition, a settings-reject indication is
displayed.
• When reaching less than 1 km/h (0.6 MPH) after decelerating from 5 km/h (3.1 MPH), a settings-reject indi-
cation is cancelled to allow settings.
• The combination meter judges a vehicle condition based on the following signals and displays a settings-
reject indication on the information display.
Setting item
Unit
Temperature
Deg C
Deg F
Dist. / Fuel
Miles, MPG
km, l/100 km
km, km/l
Setting item
Setting range
Maintenance
Service
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Tire
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Other
No setting, 500 km - 30,000 km
(No setting, 250 mile - 18,500 mile)
Setting item
Setting range
Setting unit
Alert
Driver alert
No setting, 30 min - 360 min
30 min
Outside temp
(Low temp)
ON/OFF
—
Setting item
Language
English
French
Espanol
Signal name
Signal path
Ignition signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
MWI-26
< SYSTEM DESCRIPTION >
SYSTEM (METER SYSTEM)
TIMING CHART
JSNIA2408GB
MWI
OPERATION
MWI-27
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
OPERATION
Switch Name and Function
INFOID:0000000010435910
STEERING SWITCH
METER CONTROL SWITCH
AWNIA3392ZZ
No.
Switch name
Operation
Description
1.
Enter/Up/Down switch
Press
The information display settings can be changed.
2.
Display switch
3.
Back switch
AWNIA3393ZZ
No.
Switch name
Operation
Description
1.
Illumination control switch
Press
An illuminance level of the back light of the combination meter can be adjusted.
2.
Trip reset switch
Press
• The trip meter can be switched between A and B.
• Trip meter A/B can be reset by pressing and holding the trip reset switch.
• A trip computer value displayed on the information display can be reset by
pressing and holding the trip reset switch for 1 second or more.
• All trip computer values can be reset by pressing and holding the trip reset
switch for 3 seconds or more.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст