Nissan Qashqai J11. Manual — part 737
P0705 TRANSMISSION RANGE SENSOR A
TM-523
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK N POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK P POSITION SW CIRCUIT (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK P POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
TCM
Continuity
Connector
Terminal
F1
5
4
Not existed
6
7
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F1
5
Ground
0 V
TCM
Continuity
Connector
Terminal
F1
7
4
Not existed
5
6
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F1
7
Ground
0 V
TM-524
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0705 TRANSMISSION RANGE SENSOR A
8.
CHECK R POSITION SW CIRCUIT (PART1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace malfunctioning parts.
9.
CHECK R POSITION SW CIRCUIT (PART 2)
1.
Disconnect transmission range switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning parts.
10.
CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to
TM-524, "Component Inspection"
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Component Inspection
INFOID:0000000010245601
1.
CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
TCM
Continuity
Connector
Terminal
F1
6
4
Not existed
5
7
+
−
Voltage
(Approx.)
TCM
Connector
Terminal
F1
6
Ground
0 V
Transmission range switch
Condition
Continuity
Terminal
1 – 2
Manual lever: “P” and “N” positions
Existed
Other than the above
Not existed
3 – 4
Manual lever: “P” position
Existed
Other than the above
Not existed
3 – 5
Manual lever: “R” position
Existed
Other than the above
Not existed
3 – 6
Manual lever: “N position
Existed
Other than the above
Not existed
3 – 7
Manual lever: “D” position
Existed
Other than the above
Not existed
P0705 TRANSMISSION RANGE SENSOR A
TM-525
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to
TM-526
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0706 TRANSMISSION RANGE SENSOR A
P0706 TRANSMISSION RANGE SENSOR A
DTC Logic
INFOID:0000000010245602
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
40 seconds or more.)
3.
Check the first trip DTC.
Is “P0706” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010245603
1.
ADJUSTMENT OF CONTROL CABLE
Adjust control cable. Refer to
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Results” in “TRANSMISSION”.
3.
Touch “Erase”.
4.
Perform “DTC CONFIRMATION PROCEDURE". Refer to
.
Is “P0706” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK POWER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect transmission range switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between transmission range switch harness connector terminal and ground.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0706
T/M RANGE SENSOR A
(Transmission Range Sensor
A Circuit Range/Performance)
When all of the following conditions are satis-
fied and this state is maintained for 30 sec-
onds:
• All range signals stay OFF
• TCM power supply voltage: More than 11 V
• Harness or connector
(Open circuit between ignition switch
and transmission range switch/open
circuit between transmission range
switch and TCM)
• Transmission range switch
• Control cable
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст