Nissan Qashqai J11. Manual — part 1446
P161D IMMOBILIZER
SEC-83
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DTC/CIRCUIT DIAGNOSIS
P161D IMMOBILIZER
DTC Logic
INFOID:0000000010438816
DTC DETECTION LOGIC
POSSIBLE CAUSE
BCM
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check DTC in “Self Diagnostic Result ”mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010438817
1.
REPLACE BCM
BCS-135, "Removal and Installation"
.
>> INSPECTION END
DTC No.
CONSULT screen items
DTC detecting condition
P161D
IMMOBILIZER
When BCM detects an immobilizer malfunction and engine start is prohibited.
SEC-84
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
P161E IMMOBILIZER
P161E IMMOBILIZER
DTC Logic
INFOID:0000000010438818
DTC DETECTION LOGIC
POSSIBLE CAUSE
• BCM
• ECM
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check DTC in “Self Diagnostic Result”mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010438819
1.
ECM REGISTRATION
Using CONSULT, register ECM.
Is the DTC detected?
YES
>> GO TO 2
NO
>> INSPECTION END
2.
REPLACE BCM
Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
Is the DTC detected?
YES
>> GO TO 3
NO
>> INSPECTION END
3.
REPLACE ECM
Replace ECM.
Refer to the following procedure.
• HRA2DDT:
ECH-320, "Removal and Installation"
.
ECK-398, "Removal and Installation"
• R9M:
EC9-409, "Removal and Installation"
.
• MR16DDT:
ECM-616, "Removal and Installation"
.
• MR20DD:
ECM-1031, "Removal and Installation"
>> INSPECTION END
DTC No.
CONSULT screen items
DTC detecting condition
P161E
IMMOBILIZER
When CONSULT is not used during ECM replacement.
P161F IMMOBILIZER
SEC-85
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
P161F IMMOBILIZER
DTC Logic
INFOID:0000000010438820
DTC DETECTION LOGIC
POSSIBLE CAUSE
ECM
FAIL-SAFE
Inhibit engine cranking
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010438821
1.
REPLACE ECM
Replace ECM.
Refer to the following procedure.
• HRA2DDT:
ECH-320, "Removal and Installation"
.
ECK-398, "Removal and Installation"
• R9M:
EC9-409, "Removal and Installation"
.
ECM-616, "Removal and Installation"
ECM-1031, "Removal and Installation"
>> INSPECTION END
DTC No.
CONSULT screen items
DTC detecting condition
P161F
IMMOBILIZER
When BCM detects an immobilizer malfunction and engine start is prohib-
ited.
SEC-86
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
P1616 ECM
P1616 ECM
DTC Logic
INFOID:0000000010337897
DTC DETECTION LOGIC
POSSIBLE CAUSE
ECM
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait 2 seconds or more.
2.
Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010337898
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE for DTC P1616. Refer to
Is DTC P1616 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
Replace ECM.
Refer to the following procedure.
• HRA2DDT:
ECH-320, "Removal and Installation"
.
ECK-398, "Removal and Installation"
• R9M:
EC9-409, "Removal and Installation"
.
• MR16DDT:
ECM-616, "Removal and Installation"
.
• MR20DD:
ECM-1031, "Removal and Installation"
>> INSPECTION END
DTC No.
CONSULT screen items
DTC detecting condition
P1616
NATS MALFUNCTION
ECM ROM is malfunctioning
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст