Nissan Qashqai J11. Manual — part 1713
HEADLAMP AIMING ADJUSTMENT
EXL-153
< PERIODIC MAINTENANCE >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
LHD
LHD : Description
INFOID:0000000010338844
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JMLIA5133ZZ
Headlamp LH (UP/DOWN)
adjustment screw
Headlamp LH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (UP/DOWN)
adjustment screw
: Vehicle front
Adjustment screw
Screwdriver rotation
Facing direction
Headlamp LH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
Headlamp LH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
Headlamp RH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
EXL-154
< PERIODIC MAINTENANCE >
[LED HEADLAMP]
HEADLAMP AIMING ADJUSTMENT
LHD : Aiming Adjustment Procedure
INFOID:0000000010338845
1.
Place the screen.
NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2.
Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3.
Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Never cover lens surface with tape, etc. because it is made from plastic.
4.
Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen
Headlamp RH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
Adjustment screw
Screwdriver rotation
Facing direction
Aiming adjustment area
Elbow point
Headlamp center
H.
Horizontal center line of headlamp
V.
Vertical center line of headlamp
JSLIA0030ZZ
Vertical center line of headlamp H.
Horizontal center line of headlamp
L.
Distance from headlamp center to screen
X.
Aiming adjustment area
(Lateral)
Y.
Aiming adjustment area
(Vertical)
Distance from headlamp center to screen (L)
: 10 m (32.8 ft)
JSLIA0031ZZ
HEADLAMP AIMING ADJUSTMENT
EXL-155
< PERIODIC MAINTENANCE >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Unit: mm (in)
RHD
RHD : Description
INFOID:0000000010338846
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)
Lateral direction (X)
(Right side from headlamp center line)
Highest light axis
100 (3.94)
0 - 100 (3.94)
Target light axis
100 (3.94)
Lowest light axis
130 (5.12)
JMLIA5133ZZ
Headlamp LH (UP/DOWN)
adjustment screw
Headlamp LH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (INSIDE/OUTSIDE)
adjustment screw
Headlamp RH (UP/DOWN)
adjustment screw
: Vehicle front
Adjustment screw
Screwdriver rotation
Facing direction
Headlamp LH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
EXL-156
< PERIODIC MAINTENANCE >
[LED HEADLAMP]
HEADLAMP AIMING ADJUSTMENT
RHD : Aiming Adjustment Procedure
INFOID:0000000010338847
1.
Place the screen.
NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
• Set the screen so that it is perpendicular to a level load surface.
2.
Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
3.
Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen.
CAUTION:
Never cover lens surface with tape, etc. because it is made from plastic.
4.
Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so
that it is within the aiming adjustment area.
Low beam distribution on the screen
Headlamp LH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
Headlamp RH (INSIDE/OUTSIDE)
Clockwise
INSIDE
Counterclockwise
OUTSIDE
Headlamp RH (UP/DOWN)
Clockwise
UP
Counterclockwise
DOWN
Adjustment screw
Screwdriver rotation
Facing direction
Aiming adjustment area
Elbow point
Headlamp center
H.
Horizontal center line of headlamp
V.
Vertical center line of headlamp
JSLIA0028ZZ
Vertical center line of headlamp H.
Horizontal center line of headlamp
L.
Distance from headlamp center to screen
X.
Aiming adjustment area
(Lateral)
Y.
Aiming adjustment area
(Vertical)
JSLIA0029ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст