Nissan Z (2023 year). Manual in english — page 6
Tire Pressure Unit:
The unit for tire pressure that is shown in
the vehicle information display can be
changed to:
.
psi
.
kPa
.
bar
.
kgf/cm
2
Use the scroll dial
to select and change
the unit.
If necessary, refer to the following table to
convert between units.
JVI0938X
Clock
Allows user to adjust the clock settings
and time within the vehicle information
display.
.
Display (if so equipped)
.
Clock Mode (if so equipped)
.
Clock Format
.
Daylight Saving (if so equipped)
.
Time Zone (if so equipped)
.
Set Clock Manually
The clock may also be set in the center
display. For additional information, refer
to the separate NissanConnect® Owner’s
Manual.
Vehicle Settings
The vehicle settings allows user to
change settings for the following menus.
.
Lighting
.
Turn Indicator
.
Locking
.
Wipers
The vehicle settings can be changed
using the scroll dial
.
Lighting:
The “Lighting” menu has the following
options:
.
Welcome Headlight
The welcome lighting can be set to be
Instruments and controls
2-25
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-26
Instruments and controls
ON or OFF. Use the scroll dial
to turn
this feature ON or OFF.
.
Auto Room Lamp
When this item is turned to ON, the
interior lights will illuminate if any door
is unlocked. Use the scroll dial
to
turn this feature ON or OFF.
.
Auto Headlight
The sensitivity of the Auto Headlight
can be adjusted. Use the scroll dial
to select the required sensitivity. The
following options are available:
— Turn on earliest
— Turn on earlier
— Turn on standard
— Turn on later
.
Light Off Delay
The duration of the automatic head-
lights off timer can be changed from 0
to 180 seconds. Use the scroll dial
to
change the duration.
Turn Indicator:
The “3 flashes” overtaking feature can be
changed from:
.
3 flashes
.
Continuous
Use the scroll dial
to toggle choices.
Locking:
The “Locking” menu has the following
options:
.
Ext. Door Switch (if so equipped)
When this item is turned on, the
request switch on the door is acti-
vated. Use the scroll dial
to activate
or deactivate this function.
.
Selective Unlock (if so equipped)
When this item is turned to ON, only
the driver’s door is unlocked first after
the door unlock operation. When the
door handle request switch on the
driver’s or passenger’s side door is
pushed to be unlocked, only the
corresponding door is unlocked first.
All the doors can be unlocked if the
door unlock operation is performed
again within 60 seconds. When this
item is turned to OFF, all the doors will
be unlocked after the door unlock
operation is performed once.
.
Auto Door Unlock (if so equipped)
The “Auto Door Unlock” feature allows
user to customize the auto door
unlock options. Use the scroll dial
to change the mode.
— Shift to P (if so equipped)
— IGN OFF
— OFF
.
Horn beeps on lock (if so equipped)
When this item is turned on, the horn
will chirp and the hazard indicators
will flash twice when locking the
vehicle with the Intelligent Key. Use
the scroll dial
to activate or deacti-
vate this function.
Wipers:
The “Wipers” menu has the following
options:
.
Speed Dependent
The “Speed Dependent” feature can be
activated or deactivated. Use the
scroll dial
to turn this feature ON
or OFF.
.
Drip Wipe
The “Drip Wipe” feature can be set to
be ON or OFF. Use the scroll dial
to
turn this feature ON or OFF.
Maintenance
The maintenance mode allows user to
check the distance to oil change or set
alerts for the reminding of maintenance
intervals. To change an item:
Select “Maintenance” using the scroll dial
and push it.
.
Oil Control System
.
Oil and Filter
-------------------------------------------------------------------------------------------------------------------------------------------------------------
.
Tire
.
Other
Oil Control System:
The Oil Control System informs the dis-
tance to oil change. Never exceed one
year or the following distance between oil
change intervals:
.
10,000 miles (16,000 km) for the
VR30DDTT engine
Display
when
ignition
is ON
Display timing
Action Required
Engine
Oil Ser-
vice due
in xxx
miles
Remaining oil
life is less than
940 miles (1,500
km).
Plan to have
your vehicle ser-
viced.
Engine
Oil Ser-
vice due
Remaining oil
life is 0 miles (0
km).
Have your vehi-
cle serviced
within two
weeks or less
than 500 miles
(800 km).
The oil change interval cannot be ad-
justed manually.
The distance to oil change interval is
calculated depending on the driving con-
ditions and set automatically by the oil
control system. A reminder will be dis-
played when approaching the end of the
service interval.
When the Factory Reset option is selected
in the vehicle information display, the oil
control system will also be reset to initial
value. Please change the engine oil when
Factory Reset is selected.
CAUTION
If the oil replacement indicator is
displayed, change the engine oil
within two weeks or less than 500
miles (800 km).
Operating the vehicle with deterio-
rated oil can damage the engine.
To reset oil control system:
1. Place the ignition switch in the ON
position.
2. Push the
and
buttons on the
steering wheel until “Settings” appears
in the vehicle information display. Use
the scroll dial to select “Maintenance”.
Then, push the scroll dial.
3. Select the “Oil Control System” and
push the scroll dial.
4. Push the scroll dial according to the
reset instructions displayed at the
bottom of the “Oil Control System”
maintenance screen.
When the user sets an alert for chan-
ging the engine oil in the “Oil and Filter”
menu, reset both “Oil Control System”
and “Oil and Filter” after changing the
engine oil.
Oil and Filter:
This indicator appears when user set
distance comes for changing the engine
oil and filter. You can set or reset the
distance for checking or replacing these
items. For scheduled maintenance items
and intervals, refer to the “9. Maintenance
and schedules” section.
When the user sets an alert for chan-
ging the engine oil in the “Oil and Filter”
menu, reset both “Oil Control System”
and “Oil and Filter” after changing the
engine oil.
Tire:
This indicator appears when the user set
distance comes for replacing tires. You
can set or reset the distance for replacing
tires.
WARNING
The tire replacement indicator is not
a substitute for regular tire checks,
including tire pressure checks. (See
“Changing wheels and tires” (P.8-
Instruments and controls
2-27
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-28
Instruments and controls
34).) Many factors including tire in-
flation, alignment, driving habits and
road conditions affect tire wear and
when tires should be replaced.
Setting the tire replacement indica-
tor for a certain driving distance
does not mean your tires will last
that long. Use the tire replacement
indicator as a guide only and always
perform regular tire checks. Failure
to perform regular tire checks, in-
cluding tire pressure checks could
result in tire failure. Serious vehicle
damage could occur and may lead to
a collision, which could result in
serious personal injury or death.
Other:
This indicator appears when the user set
distance comes for checking or replacing
maintenance items other than the engine
oil, oil filter and tires. Other maintenance
items can include such things as air filter
or tire rotation. You can set or reset the
distance for checking or replacing the
items.
Customize Display
The display settings allows user to
choose from the various meter selections.
The display settings can be changed
using the scroll dial
.
Main Menu Selection:
Displays available screens that can be
shown in the vehicle information display.
Route Guidance (if so equipped):
To change the setting, use the scroll dial
to select and push it.
.
Alerts
The “Alerts” allows user to turn the
Navigation Settings alerts on or off.
Welcome Effect:
The “Welcome Effect” displays the avail-
able welcome effect settings.
.
Animation
Unit/Language
The units that are shown in the vehicle
information display can be changed:
.
Mileage/Fuel
.
Tire Pressure
.
Temperature
.
Language
Use the scroll dial
to select and change
the units of the vehicle information dis-
play.
Mileage/Fuel:
The unit for the mileage that is shown in
the vehicle information display can be
changed.
.
miles, MPG
.
km, km/l
.
km, l/100km
Use the scroll dial
to select and change
the unit.
Tire Pressure:
The unit for tire pressures that is shown
in the vehicle information display can be
changed to:
.
psi
.
kPa
.
bar
.
kgf/cm
2
(See “TPMS Setting” (P.2-24).)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Temperature:
The temperature that is shown in the
vehicle information display can be chan-
ged from:
.
°C
.
°F
Use the scroll dial
to toggle choices.
Language:
The language of the vehicle information
display can be changed.
Use the scroll dial
to select and change
the language of the vehicle information
display.
Factory Reset
The settings in the vehicle information
display can be reset back to the factory
default. To reset the vehicle information
display:
1. Select “Factory Reset” using the scroll
dial
and push it.
2. Select “Yes” to return all settings back
to default by pushing the scroll dial .
Instruments and controls
2-29
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-30
Instruments and controls
WAC0905X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WAC0906X
Instruments and controls
2-31
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-32
Instruments and controls
VEHICLE INFORMATION DISPLAY
WARNINGS AND INDICATORS
The displayed images may differ depend-
ing on the model.
1. Engine start operation indicator
(Automatic transmission models)
This indicator appears when the shift
position is in the P (Park) position.
This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed. You can start
the engine directly in any position of the
ignition switch.
2. Engine start operation indicator
(Manual Transmission models)
This indicator means that the engine will
start by pushing the ignition switch with
the clutch pedal depressed.
3. No Key Detected warning
The warning appears when the door is
closed with the Intelligent Key left outside
the vehicle and the ignition switch in the
ACC or ON position. Make sure that the
Intelligent Key is inside the vehicle.
See “Intelligent Key system” (P.3-6) for
more details.
4. Intelligent Key battery discharge
indicator
This indicator appears when the Intelli-
gent Key battery is running out of power.
If this indicator appears, replace the
battery with a new one. (See “Intelligent
Key battery replacement” (P.8-21).)
5. Engine start operation for Intelli-
gent Key system indicator
This indicator appears when the Intelli-
gent Key battery is running out of power
and when the Intelligent Key system and
vehicle are not communicating normally.
If this indicator appears, touch the igni-
tion switch with the Intelligent Key while
depressing the brake pedal. (See “Intelli-
gent Key battery discharge” (P.5-13).)
6. Key System Error: See Owner’s
Manual warning
This warning appears if there is a mal-
function in the Intelligent Key system.
If this warning appears while the engine is
stopped, the engine cannot be started. If
this warning appears while the engine is
running, the vehicle can be driven. How-
ever, it is recommended that you visit a
NISSAN dealer for repair as soon as
possible.
7. Parking brake release warning
This warning appears when the vehicle
speed is above 4 MPH (7 km/h) and the
parking brake is applied.
8. Low Fuel warning
This warning appears when the fuel level
in the fuel tank is getting low. Refuel as
soon as it is convenient, preferably before
the fuel gauge reaches 0 (Empty). There
will be a small reserve of fuel in the tank
when the fuel gauge needle reaches 0
(Empty).
9. Loose Fuel Cap warning
This warning appears when the fuel-filler
cap is not tightened correctly after the
vehicle has been refueled. (See “Fuel-filler
cap” (P.3-19).)
10. Low Washer Fluid warning
This warning appears when the window
washer fluid is at a low level. Add window
washer fluid as necessary. For additional
information, refer to “Window washer
fluid” (P.8-11).
-------------------------------------------------------------------------------------------------------------------------------------------------------------
11. Door/rear hatch open warning
This warning appears if any of the doors
and/or the rear hatch are open or not
closed securely. The vehicle icon indicates
which door or the rear hatch is open on
the display.
12. Tire Pressure Low — Add Air
warning
This warning appears when the low tire
pressure warning light in the meter
illuminates and low tire pressure is de-
tected. The warning appears each time
the ignition switch is placed in the ON
position as long as the low tire pressure
warning light remains illuminated. If this
warning appears, stop the vehicle and
adjust the pressure to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. (See “Low tire
pressure warning light” (P.2-18) and “Tire
Pressure Monitoring System (TPMS)” (P.5-
5).)
13. Shift to P range warning (Auto-
matic transmission models)
This warning appears when the driver’s
door is opened while the shift lever is in
any position other than P (Park).
If this warning appears, push the park
button to engage the P (Park) position.
An inside warning chime will also sound.
(See “Intelligent Key system” (P.3-6).)
14. AT Malfunction Service now
warning (Automatic transmission
models)
This warning appears when there is a
malfunction with the AT system. If this
warning appears, have the system
checked. It is recommended that you visit
a NISSAN dealer for this service.
15. AT hot Power reduced warning
(Automatic transmission models)
The AT has a high fluid temperature
protection mode. If the fluid temperature
becomes too high (for example, climbing
steep grades in high temperatures with
heavy loads), engine power and, under
some conditions, vehicle speed will be
decreased automatically to reduce the
chance of transmission damage. Vehicle
speed can be controlled with the accel-
erator pedal, but the engine and vehicle
speed may be reduced.
16. AT Malfunction Stop safely
warning (Automatic transmission
models)
This warning appears when there is a
malfunction with the AT system. If this
warning appears, stop the vehicle in a
safe place. Have the system checked. It is
recommended you visit a NISSAN dealer
for this service.
17. Stop the vehicle warning (Auto-
matic transmission models)
This warning appears when the AT sys-
tem judges the vehicle is reversed on an
uphill road with the shift position in D
(Drive), or moved forward on a downhill
road with the shift position in R (Reverse).
The engine may stall, so stop the vehicle
movement by depressing the brake ped-
al.
18. Service AT Power reduced
warning (Automatic transmission
models)
This warning appears when the AT power
is reduced. If this warning appears, have
the system checked. It is recommended
that you visit a NISSAN dealer for this
service.
19. Check position of shift lever
warning (if so equipped)
This warning appears if the system can-
not detect the shift position. Make sure
the vehicle is placed in a position properly.
Have the system checked. It is recom-
mended you contact a NISSAN dealer for
this service.
Instruments and controls
2-33
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-34
Instruments and controls
20. When parked apply parking
brake warning (Automatic trans-
mission models)
This warning appears if a malfunction
occurs in the electric shift control system.
Contact a NISSAN dealer as soon as
possible. When parking the vehicle, make
sure that the parking brake is applied. If
the parking brake is not applied, the
ignition switch may not be turned off.
21. Automatic Transmission (AT)
position indicator (Automatic
transmission models)
This indicator shows the AT shift position.
In the manual shift mode, when the
transmission does not shift to the se-
lected gear due to a transmission protec-
tion mode, the AT position indicator will
blink and a chime will sound.
See “Automatic transmission” (P.5-15) for
further details.
22. Shipping Mode On Push Storage
Fuse warning (if so equipped)
This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended
storage switch to turn off the warning.
(See “Extended storage fuse switch” (P.8-
20).)
23. Power will turn off to save the
battery warning
Under the specific conditions, this warn-
ing may appear after the ignition switch is
in the ON position for a certain period of
time.
24. Power turned off to save the
battery warning
Under the specific conditions, this warn-
ing may appear after the ignition switch is
automatically turned OFF to save the
battery.
25. Reminder Turn OFF Headlights
warning
This warning appears when the driver
side door is opened with the headlight
switch is left ON and the ignition switch is
placed in the OFF position. Place the
headlight switch in OFF (if so equipped)
or AUTO position. For additional informa-
tion, (See “Headlight and turn signal
switch” (P.2-46).)
26. Headlight System Error: See
Owner’s Manual warning
This warning appears if the LED head-
lights are malfunctioning. Have the sys-
tem checked. It is recommended that you
visit a NISSAN dealer for this service.
27. Time for a break? indicator
This indicator appears when the set
Timer Alert activates. You can set the
time for up to 6 hours.
28. Lane Departure Warning (LDW)
indicator
This indicator appears when the Lane
Departure Warning (LDW) system is en-
gaged.
(See “Lane Departure Warning (LDW)” (P.5-
29).)
29. Blind Spot Warning (BSW) indi-
cator
This indicator appears when the Blind
Spot Warning (BSW) system is engaged.
(See “Blind Spot Warning (BSW)” (P.5-34).)
30. Vehicle ahead detection indi-
cator
This indicator shows the status of the
following systems:
.
Automatic Emergency Braking (AEB)
with Pedestrian Detection
.
Intelligent Forward Collision Warning
(I-FCW)
(See “Automatic Emergency Braking (AEB)
with Pedestrian Detection system” (P.5-
63) or “Intelligent Forward Collision Warn-
ing (I-FCW)” (P.5-81).)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
31. Cruise indicator
This indicator shows the conventional
(fixed speed) cruise control mode status.
The status is shown by the color.
(See “Conventional (fixed speed) cruise
control mode” (P.5-59).)
32. Speed control status/set dis-
tance indicator
This indicator shows the status of the
Intelligent Cruise Control (ICC) system.
The status is shown by the color and
shape. (See “Intelligent Cruise Control
(ICC)” (P.5-43).)
33. Malfunction See Owner’s Man-
ual warning
This warning appears when the following
systems malfunction.
.
Lane Departure Warning (LDW)
.
Blind Spot Warning (BSW)
.
Intelligent Cruise Control (ICC)
.
Automatic Emergency Braking (AEB)
with Pedestrian Detection
.
Rear Cross Traffic Alert (RCTA)
.
Intelligent Forward Collision Warning
(I-FCW)
.
Intelligent Driver Alertness (I-DA)
(See “Lane Departure Warning (LDW)” (P.5-
29), “Blind Spot Warning (BSW)” (P.5-34),
“Intelligent Cruise Control (ICC)” (P.5-43),
“Automatic Emergency Braking (AEB) with
Pedestrian Detection system” (P.5-63),
“Rear Cross Traffic Alert (RCTA)” (P.5-74),
“Intelligent Forward Collision Warning (I-
FCW)” (P.5-81) or “Intelligent Driver Alert-
ness (I-DA)” (P.5-90).)
34. Unavailable Camera Tempera-
ture High warning
This warning appears if the interior tem-
perature of the vehicle has reached such
a high temperature that the sensor for
the following system can no longer func-
tion reliably.
.
Lane Departure Warning (LDW)
Once the interior temperature has
reached normal levels, the warning
should disappear.
If the warning continues to display, have
the system checked. It is recommended
that you visit a NISSAN dealer for this
service.
For additional information, refer to “Lane
Departure Warning (LDW)” (P.5-29).
35. Launch Control indicator (if so
equipped)
This indicator appears when the Launch
Control system is engaged.
(See “Launch Control” (P.5-26).)
36. Currently Unavailable warning
This warning appears when the Intelli-
gent Cruise Control (ICC) system be-
comes unavailable in the following
conditions:
.
The Vehicle Dynamic Control (VDC)
system is turned off
For additional information, refer to “In-
telligent Cruise Control (ICC)” (P.5-43).
37. Forward Driving Aids tempora-
rily disabled Front Sensor blocked
warning
If the front radar sensor area on the front
of the vehicle is covered with dirt or
obstructed, making it impossible to de-
tect a vehicle ahead, the following system
is automatically turned off.
.
Intelligent Cruise Control (ICC)
.
Automatic Emergency Braking (AEB)
with Pedestrian Detection
.
Intelligent Forward Collision Warning
(I-FCW)
If the warning message appears, park the
Instruments and controls
2-35
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-36
Instruments and controls
vehicle in a safe location and turn the
engine off.
Check to see if the sensor area is blocked.
If the sensor area is blocked, remove the
blocking material. Restart the engine. If
the warning message continues to ap-
pear, have the system checked. It is
recommended that you visit a NISSAN
dealer for this service.
For more details, see “Intelligent Cruise
Control (ICC)” (P.5-43), “Automatic Emer-
gency Braking (AEB) with Pedestrian De-
tection system” (P.5-63) or “Intelligent
Forward Collision Warning (I-FCW)” (P.5-
81).
38. Unavailable Side Radar Ob-
struction warning
This warning appears when the following
systems become unavailable because a
radar blockage is detected.
.
Blind Spot Warning (BSW)
.
Rear Cross Traffic Alert (RCTA)
(See “Blind Spot Warning (BSW)” (P.5-34) or
“Rear Cross Traffic Alert (RCTA)” (P.5-74).)
39. Unavailable Slippery Road
warning
This warning appears when the following
system become unavailable because the
road is slippery.
.
Intelligent Cruise Control (ICC)
(See “Intelligent Cruise Control (ICC)” (P.5-
43).)
40. Automatic Emergency Braking
(AEB) emergency warning indicator
This warning indicator appears along
with an audible warning, when the Auto-
matic Emergency Braking (AEB) with Pe-
destrian Detection system detects the
possibility of a forward collision.
See “Automatic Emergency Braking (AEB)
with Pedestrian Detection system” (P.5-
63).
41. Sonar system indicator
This indicator appears to indicate the
status of the sonar system.
See “Front and rear sonar system” (P.5-
93).
42. Parking Sensor Error warning
This warning appears when there is a
malfunction with the sonar system. (See
“Front and rear sonar system” (P.5-93).)
43. Take a Break? indicator
This indicator appears when the Intelli-
gent Driver Alertness (I-DA) system detect
that the driver attention is decreasing.
(See “Intelligent Driver Alertness (I-DA)”
(P.5-90).)
44. Neutral Hold Mode guidance
indicator (Automatic transmission
models)
This indicator appears when the ignition
switch is placed in the OFF position while
the shift position is in the N (Neutral)
position (Neutral hold mode is available).
(See “Neutral hold mode function” (P.5-
18).)
45. Neutral Hold Mode activated
indicator (Automatic transmission
models)
This indicator appears when the Neutral
hold mode is activated. To exit the Neutral
hold mode, place the vehicle in other than
N (Neutral) position. (See “Neutral hold
mode function” (P.5-18).)
-------------------------------------------------------------------------------------------------------------------------------------------------------------
46. Neutral Hold Mode was not
activated indicator (Automatic
transmission models)
This indicator appears when the Neutral
hold mode is unavailable. To activate the
Neutral hold mode, wait for a while with-
out shifting and then perform the opera-
tions again. (See “Neutral hold mode
function” (P.5-18).)
47. Engine Oil Service due in – – –
miles
This distance to oil change is displayed if
the distance to oil change is less than 62
miles (100 km).
48. Drive Mode Selector indicator
(Automatic transmission models)
When a driving mode is selected using the
Drive Mode Selector, the selected mode
indicator is displayed.
.
SPORT
.
STANDARD
(See “Drive Mode Selector” (P.5-21).)
Instruments and controls
2-37
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-38
Instruments and controls
WAC0907X
-------------------------------------------------------------------------------------------------------------------------------------------------------------
WAC0908X
TRIP COMPUTER
Switches for the trip computer are lo-
cated on the left side of the steering
wheel.
Scroll dial - navigate through the items
and change or select an item in vehicle
information display
this scroll dial allows up/down navigation
and push to select
- go back to the previous menu
- change from one display screen
to the next (i.e. trip, Fuel economy)
The displayed images may differ depend-
ing on the model.
1. Home (if so equipped)
The Home mode shows the following
information.
.
Vehicle speed
.
Navigation
.
Audio
2. Drive Computer
Average fuel consumption:
The average fuel consumption shows the
average fuel consumption since the last
reset.
Average speed:
The average speed shows the average
vehicle speed since the last reset.
Trip odometer:
The trip odometer shows the total dis-
tance the vehicle has been driven since
the last reset.
Elapsed time:
The elapsed time shows the time since
the last reset.
The Drive Computer mode have three
modes of operation. You can switch
between Manual Reset1, Manual Reset2
or Auto Refuel by pushing the scroll dial
.
Manual Reset1 and Manual Reset2 can be
reset manually by using the scroll dial
.
Auto Refuel will be reset automatically
each time when refueling.
3. Fuel Economy display
Current fuel consumption:
The Fuel economy display mode shows
the current fuel consumption.
Average fuel consumption:
The Fuel economy display mode shows
the average fuel consumption since the
last reset.
The Fuel economy display mode have
three modes of operation. You can switch
between Manual Reset1, Manual Reset2 or
Auto Refuel by pushing the scroll dial
.
Manual Reset1 and Manual Reset2 can be
reset manually by using the scroll dial
.
Auto Refuel will be reset automatically
each time when refueling.
4. Tire Pressures
The tire pressure mode shows the pres-
sure of all four tires while the vehicle is
driven.
When the Tire Pressure Low — Add Air
warning appears, the display can be
switched to the tire pressure mode by
pushing the scroll dial
to reveal addi-
tional details on the displayed warning.
Instruments and controls
2-39
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-40
Instruments and controls
5. Compass (if so equipped)
This display indicates the heading direc-
tion of the vehicle.
6. Navigation (if so equipped)
When the route guidance is set in the
navigation system, this item shows the
navigation route information.
7. Audio
The audio mode shows the status of
audio information.
8. Driver Assistance
The Driver Assistance mode shows the
operating condition for the following
systems.
.
Forward:
— Automatic Emergency Braking
(AEB) with Pedestrian Detection
system
— Intelligent Forward Collision Warn-
ing (I-FCW)
.
Lane:
— Lane Departure Warning (LDW)
.
Blind Spot:
— Blind Spot Warning (BSW)
For more details, see “Lane Departure
Warning (LDW)” (P.5-29), “Blind Spot Warn-
ing (BSW)” (P.5-34), “Automatic Emergency
Braking (AEB) with Pedestrian Detection
system” (P.5-63) or “Intelligent Forward
Collision Warning (I-FCW)” (P.5-81).
9. Intelligent Cruise Control (ICC)
system
This mode shows the operating condition
for the Intelligent Cruise Control (ICC)
system. (See “Intelligent Cruise Control
(ICC)” (P.5-43).)
WAC0521X
CLOCK AND OUTSIDE AIR TEM-
PERATURE
The clock
and outside air temperature
are displayed on the upper side of the
vehicle information display.
Clock
For clock adjustment, see “Clock” (P.2-25)
or the separate NissanConnect® Owner’s
Manual.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст