Qashqai J11. Rear suspension — part 2
REAR SUSPENSION MEMBER
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000010297275
FOR 2WD GOM AND 4WD
Removal and Installation
INFOID:0000000010297276
REMOVAL
1.
Remove tires from vehicle.
2.
Remove main muffler. Refer to
(K9K),
(R9M),
(HRA2DDT) and
(MR16DDT).
3.
Remove coil spring. Refer to
4.
Remove lower link. Refer to
.
5.
Remove upper link. Refer to
.
6.
Remove rear stabilizer bar. Refer to
.
7.
Remove rear drive shaft. Refer to
8.
Remove rear propeller shaft (4WD). Refer to
.
9.
Remove rear final drive (4WD). Refer to
.
10. Remove shock absorber. Refer to
11. Set suitable jack under rear suspension member.
12. Remove mounting nuts and bolts from rear suspension member.
13. Slowly lower jack, then remove rear suspension member, lower link and upper link from vehicle as a unit.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
E1EIA0124GB
1.
Rear suspension member
2.
Suspension member stay (RH)
3.
Suspension member stay (LH)
4.
Bound bumper
: Front
Refer to
for symbols in the figure.
RSU-18
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
14. Perform the inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• When installing suspension member stay, face each arrow on the part toward the inside of the vehicle.
• Align the matching marks made during removal when reusing the disc brake rotor.
• Perform the final tightening of each parts removed when removing rear suspension assembly under unladen
conditions.
• Check wheel sensor harness for proper connection.
• Perform the inspection after installation. Refer to
Inspection
INFOID:0000000010297277
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust parking brake operation. Refer to
.
2.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
3.
Adjust neutral position of steering angle sensor. Refer to
.
REAR SUSPENSION ASSEMBLY
RSU-19
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000010297278
Removal and Installation
INFOID:0000000010297279
REMOVAL
Refer to procedure from 1 to 14 in
RSU-17, "Removal and Installation"
1.
Rear suspension member
2.
Suspension member stay (right side) 3.
Suspension member stay (left side)
4.
Stabilizer bar
5.
Stabilizer bushing
6.
Stabilizer clamp
7.
Stabilizer link
8.
Suspension bar
9.
Suspension arm bracket
10. Arm stopper
11. Suspension arm
12. Low rubber seat
13. Coil spring
14. Upper rubber seat
15. lower link
16. Upper link
17. Bound bumper
18. Shock absorber
19. Cam bolt
20. Cam washer
: Front
Refer to
for symbols in the figure.
E1EIA0125GB
RSU-20
< UNIT REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each parts removed when removing rear suspension assembly under unladen
conditions.
• Check wheel sensor harness for proper connection. Refer to
.
Inspection
INFOID:0000000010297280
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust parking brake operation. Refer to
.
2.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
3.
Adjust neutral position of steering angle sensor. Refer to
.
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000010297281
TC models
For Europe / SAF / GOM
Measure value under unladen* conditions.
*: 90% fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Russie
Measure value under unladen* conditions.
*: 90% fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Australia
Measure value under unladen* conditions.
*: 90% fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
HT models
For Europe / SAF / GOM
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–0
°
25
′
(–0.42
°
)
Nominal
–0
°
55
′
(–0.92
°
)
Maximum
–1
°
25
′
(–1.42
°
)
Total toe-in
Distance
Nominal
In 1.8 mm (0.07 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
05
′
(0.08
°
)
Nominal
In 0
°
10
′
(0.17
°
)
Maximum
In 0
°
15
′
(0.25
°
)
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–0
°
25
′
(–0.42
°
)
Nominal
–0
°
55
′
(–0.92
°
)
Maximum
–1
°
25
′
(–1.42
°
)
Total toe-in
Distance
Nominal
In 1.7 mm (0.07 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
05
′
(0.08
°
)
Nominal
In 0
°
10
′
(0.17
°
)
Maximum
In 0
°
15
′
(0.25
°
)
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–0
°
25
′
(–0.42
°
)
Nominal
–0
°
55
′
(–0.92
°
)
Maximum
–1
°
25
′
(–1.42
°
)
Total toe-in
Distance
Nominal
In 1.9 mm (0.07 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
05
′
(0.08
°
)
Nominal
In 0
°
10
′
(0.17
°
)
Maximum
In 0
°
15
′
(0.25
°
)
Tire size
215/65R16
215/60R17
225/45R19
Camber
Degree minute (Decimal degree)
Minimum
–1
°
00
′
(–1.00
°
)
Nominal
–1
°
30
′
(–150
°
)
Maximum
–2
°
00
′
(–2.00
°
)
RSU-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Measure value under unladen* conditions.
*: 90% fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Wheelarch Height
INFOID:0000000010683831
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Maximum difference in deviation from nominal between all wheelarch height is 15 mm (0.59 in).
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Maximum difference in deviation from nominal between all wheelarch height is 15 mm (0.59 in).
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Maximum difference in deviation from nominal between all wheelarch height is 15 mm (0.59 in).
Total toe-in
Distance
Nominal
In 5.5 mm (0.22 in)
Angle
Degree minute (Decimal degree)
Minimum
In 0
°
02
′
(0.03
°
)
Nominal
In 0
°
25
′
(0.42
°
)
Maximum
In 0
°
48
′
(0.80
°
)
Applied model
HRA2DDT
Destination
Europe
Russie / SAF / GOM
Tire size
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
Rear (Hr)
775 mm
(30.51 in)
774 mm
(30.47 in)
784 mm
(30.87 in)
783 mm
(30.83 in)
SFA746B
Applied model
MR20DD
Destination
Russie / Australia
SAF / GOM
Tire size
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
Rear (Hr)
783 mm
(30.83 in)
784 mm
(30.87 in)
783 mm
(30.83 in)
784 mm
(30.87 in)
783 mm
(30.83 in)
784 mm
(30.87 in)
Applied model
K9K
Destination
Europe
SAF / GOM
Tire size
215/65R16
215/60R17
225/45R19
215/60R17
225/45R19
Rear (Hr)
774 mm
(30.47 in)
773 mm
(30.43 in)
783 mm
(30.83 in)
784 mm
(30.87 in)
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-23
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Maximum difference in deviation from nominal between all wheelarch height is 15 mm (0.59 in).
Measure value under unladen* conditions.
*: 90% Fuel. Engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Maximum difference in deviation from nominal between all wheelarch height is 15 mm (0.59 in).
Applied
model
R9M
Destina-
tion
Europe 2WD
Europe 4WD
Russie / SAF / GOM / Australia
Tire size
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
215/65R16
215/60R17
225/45R19
Rear (Hr)
774 mm
(30.47 in)
773 mm
(30.43 in)
784 mm
(30.87 in)
783 mm
(30.83 in)
784 mm
(30.87 in)
783 mm
(30.83 in)
Applied model
MR16DDT
Destination
Europe
Tire size
215/65R16
215/60R17
225/45R19
215/60R17
225/45R19
Rear (Hr)
774 mm
(30.47 in)
773 mm
(30.43 in)
784 mm
(30.87 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст