Qashqai J11. SRS Airbag control system — part 4
B0021 CURTAIN AIR BAG MODULE
SRC-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0021 CURTAIN AIR BAG MODULE
DTC Description
INFOID:0000000010431044
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0021–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of curtain air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
[B0021–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of curtain air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
[B0021–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of curtain air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
[B0021–09, B0021–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of curtain air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431045
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0021–09
CURTAIN A/B MODULE LH
[Left Curtain Deployment Control 1 (Subfault)]
Curtain air bag module LH circuits are shorted to each other
B0021–11
Curtain air bag module LH circuit is shorted to ground
B0021–12
Curtain air bag module LH circuit is shorted to power supply circuit
B0021–13
Curtain air bag module LH circuit is open
B0021–1A
Curtain air bag module LH circuits are shorted to each other
SRC-50
< DTC/CIRCUIT DIAGNOSIS >
B0021 CURTAIN AIR BAG MODULE
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE CURTAIN AIR BAG MODULE LH
1.
Replace curtain air bag module LH. Refer to
SR-21, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0028 SIDE AIR BAG MODULE
SRC-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0028 SIDE AIR BAG MODULE
DTC Description
INFOID:0000000010431046
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0028–09, B0028–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431047
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0028–09
SIDE A/B MODULE RH
[Right Side Airbag Deployment Control (Sub-
fault)]
Side air bag module RH circuits are shorted to each other
B0028–11
Side air bag module RH circuit is shorted to ground
B0028–12
Side air bag module RH circuit is shorted to power supply circuit
B0028–13
Side air bag module RH circuit is open
B0028–1A
Side air bag module RH circuits are shorted to each other
SRC-52
< DTC/CIRCUIT DIAGNOSIS >
B0028 SIDE AIR BAG MODULE
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SIDE AIR BAG MODULE RH
1.
Replace side air bag module RH. Refer to
SR-23, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0029 CURTAIN AIR BAG MODULE
SRC-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0029 CURTAIN AIR BAG MODULE
DTC Description
INFOID:0000000010431048
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0029–09, B0029–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431049
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0029–09
CURTAIN A/B MODULE RH
[Right Curtain Deployment Control 1 (Sub-
fault)]
Curtain air bag module RH circuits are shorted to each other
B0029–11
Curtain air bag module RH circuit is shorted to ground
B0029–12
Curtain air bag module RH circuit is shorted to power supply circuit
B0029–13
Curtain air bag module RH circuit is open
B0029–1A
Curtain air bag module RH circuits are shorted to each other
SRC-54
< DTC/CIRCUIT DIAGNOSIS >
B0029 CURTAIN AIR BAG MODULE
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE CURTAIN AIR BAG MODULE RH
1.
Replace curtain air bag module RH. Refer to
SR-21, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0091 B-PILLAR SATELLITE SENSOR
SRC-55
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0091 B-PILLAR SATELLITE SENSOR
DTC Description
INFOID:0000000010431050
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0091–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of satellite sensor LH
• Internal malfunction of air bag diagnosis sensor unit
[B0091–23, B0091–24, B0091–25, B0091–28
• Internal malfunction of satellite sensor LH
• Internal malfunction of air bag diagnosis sensor unit
[B0091–81, B0091–93]
• Connection malfunction of harness or connector
• Internal malfunction of satellite sensor LH
• Internal malfunction of air bag diagnosis sensor unit
[B0091–86]
• Air bag diagnosis sensor unit and satellite sensor LH is different from the part specified
[B0091–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of satellite sensor LH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431051
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0091–11
B-PILLAR SAT SEN LH
[Left Side Restraints Sensor 1 (Subfault)]
Satellite sensor LH circuit is shorted to ground
B0091–23
Lower limit value malfunction of satellite sensor LH
B0091–24
Upper limit value malfunction of satellite sensor LH
B0091–25
Diagnosis malfunction of satellite sensor LH
B0091–28
Offset malfunction of satellite sensor LH
B0091–81
Communication malfunction of satellite sensor LH
B0091–86
Satellite sensor LH is out of the specified specification
B0091–88
Satellite sensor LH circuit is open
B0091–93
Reset malfunction of satellite sensor LH
SRC-56
< DTC/CIRCUIT DIAGNOSIS >
B0091 B-PILLAR SATELLITE SENSOR
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0091–86]>> GO TO 4.
Other than the above>> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
REPLACE SATELLITE SENSOR LH
1.
Replace satellite sensor LH. Refer to
SR-26, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0094 CRASH ZONE SENSOR
SRC-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0094 CRASH ZONE SENSOR
DTC Description
INFOID:0000000010431052
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0094–81, B0094–93]
• Connection malfunction of harness or connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–86]
• Air bag diagnosis sensor unit and crash zone sensor is different from the part specified
[B0094–23, B0094–24, B0094–25, B0094–28]
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431053
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0094–11
CRASH ZONE SENS
[Center Frontal Restraints Sensor (Subfault)]
Crash zone sensor circuit is shorted to ground
B0094–23
Lower limit value malfunction of crash zone sensor
B0094–24
Upper limit value malfunction of crash zone sensor
B0094–25
Diagnosis malfunction of crash zone sensor
B0094–28
Offset malfunction of crash zone sensor
B0094–81
Communication malfunction of crash zone sensor
B0094–86
Crash zone sensor is out of the specified specification
B0094–88
Crash zone sensor circuit is open
B0094–93
Reset malfunction of crash zone sensor
SRC-58
< DTC/CIRCUIT DIAGNOSIS >
B0094 CRASH ZONE SENSOR
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0094–86]>> GO TO 4.
Other than the above>> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
REPLACE CRASH ZONE SENSOR
1.
Replace crash zone. Refer to
SR-24, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B0096 B-PILLAR SATELLITE SENSOR
SRC-59
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0096 B-PILLAR SATELLITE SENSOR
DTC Description
INFOID:0000000010431054
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0096–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–23, B0096–24, B0096–25, B0096–28
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–81, B0096–93]
• Connection malfunction of harness or connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
[B0096–86]
• Air bag diagnosis sensor unit and satellite sensor RH is different from the part specified
[B0096–88]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431055
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0096–11
B-PILLAR SAT SEN RH
[Right Frontal Restraints Sensor 1(Subfault)]
Satellite sensor RH circuit is shorted to ground
B0096–23
Lower limit value malfunction of satellite sensor RH
B0096–24
Upper limit value malfunction of satellite sensor RH
B0096–25
Diagnosis malfunction of satellite sensor RH
B0096–28
Offset malfunction of satellite sensor RH
B0096–81
Communication malfunction of satellite sensor RH
B0096–86
Satellite sensor RH is out of the specified specification
B0096–88
Satellite sensor RH circuit is open
B0096–93
Reset malfunction of satellite sensor RH
SRC-60
< DTC/CIRCUIT DIAGNOSIS >
B0096 B-PILLAR SATELLITE SENSOR
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0096–86] >> GO TO 4.
Other than the above >> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
REPLACE SATELLITE SENSOR RH
1.
Replace satellite sensor RH. Refer to
SR-26, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B00D2 FRONT PASSENGER AIR BAG ON INDICATOR
SRC-61
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B00D2 FRONT PASSENGER AIR BAG ON INDICATOR
DTC Description
INFOID:0000000010431032
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B00D2–04]
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D2–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D2–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D2–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D2–15]
• Connection malfunction or short circuit to power supply of harness and connector
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431033
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B00D2–04
PASS A/B ON INDCTR CIRC
[Restraint System Malfunction Indicator 1
(Subfault)]
Malfunction in front passenger air bag ON indicator circuit
B00D2–11
Front passenger air bag ON indicator circuit is shorted to ground
B00D2–12
Front passenger air bag ON indicator circuit is shorted to power supply
circuit
B00D2–13
Front passenger air bag ON indicator circuit is open
B00D2–15
Front passenger air bag ON indicator circuit is open or shorted to power
supply circuit
SRC-62
< DTC/CIRCUIT DIAGNOSIS >
B00D2 FRONT PASSENGER AIR BAG ON INDICATOR
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK FRONT PASSENGER AIR BAG ON INDICATOR
1.
Replace indicator unit. Refer to
HAC-126, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR
SRC-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR
DTC Description
INFOID:0000000010431034
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B00D5–04]
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–15]
• Connection malfunction or short circuit to power supply of harness and connector
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES
>> Refer to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010431035
WARNING:
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B00D5–04
PASS A/B INDCTR CKT
[Restraint System Passenger Disable Indica-
tor (Subfault)]
Malfunction in front passenger air bag OFF indicator circuit
B00D5–11
Front passenger air bag OFF indicator circuit is shorted to ground
B00D5–12
Front passenger air bag OFF indicator circuit is shorted to power supply
circuit
B00D5–13
Front passenger air bag OFF indicator circuit is open
B00D5–15
Front passenger air bag OFF indicator circuit is open or shorted to pow-
er supply circuit
SRC-64
< DTC/CIRCUIT DIAGNOSIS >
B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK FRONT PASSENGER AIR BAG OFF INDICATOR
1.
Replace indicator unit. Refer to
HAC-126, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст