Nissan Maxima. Manual — part 18
ADP-64
< DTC/CIRCUIT DIAGNOSIS >
SEAT MEMORY SWITCH
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace seat memory switch. Refer to
ADP-171, "Removal and Installation"
.
Terminal
Condition
Continuity
Seat memory switch
4
1
Memory switch 1
Push
Yes
Release
No
2
Memory switch 2
Push
Yes
Release
No
3
Set switch
Push
Yes
Release
No
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-65
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000010051759
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000010051760
1.
CHECK FUNCTION
1. Select “MIR CHNG SW-R”, “MIR CHNG SW-L” in “DATA MONITOR” mode with CONSULT.
2. Check changeover switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-65, "CHANGEOVER SWITCH : Diagnosis Proce-
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000010051761
Regarding Wiring Diagram information, refer to
1.
CHECK CHANGEOVER SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> GO TO 2
2.
CHECK HARNESS CONTINUITY
Monitor item
Condition
Status
MIR CHNG SW-R
Mirror switch (right)
Operate
ON
Release
OFF
MIR CHNG SW-L
Mirror switch (left)
Operate
ON
Release
OFF
Terminals
Change over switch
condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control
unit connector
Terminal
M63
2
Ground
RIGHT
0
Other than above
5
14
LEFT
0
Other than above
5
ALJIA0393ZZ
ADP-66
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror remote control switch.
3. Check continuity between automatic drive positioner control unit
connector and door mirror remote control switch connector.
4. Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK CHANGEOVER SWITCH
Check changeover switch.
ADP-66, "CHANGEOVER SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
GI-41, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-170, "Removal and Installation"
NO
>> Repair or replace the malfunctioning parts.
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000010051762
1.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch.
Automatic drive
positioner control
unit connector
Terminal
Door mirror re-
mote control
switch connector
Terminal
Continuity
M63 (A)
2
M108 (B)
3
Yes
14
2
ALJIA0394ZZ
Automatic drive positioner control unit connector
Terminal
Ground
Continuity
M63 (A)
2
No
14
Door mirror remote control switch
connector
Terminal
Ground
Continuity
M108
13
Yes
ALJIA0395ZZ
Terminal
Change over switch
condition
Continuity
Door mirror remote control switch
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-67
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace door mirror remote control switch. Refer to
MIRROR SWITCH
MIRROR SWITCH : Description
INFOID:0000000010051763
It operates angle of the door mirror face.
It transmits mirror face adjust operation to automatic drive positioner control unit.
MIRROR SWITCH : Component Function Check
INFOID:0000000010051764
1.
CHECK FUNCTION
1. Select “MIR CON SW-UP/DN”,“MIR CON SW-RH/LH “ in “DATA MONITOR” mode with CONSULT.
2. Check mirror switch signal under the following conditions.
Is the indication normal?
YES
>> Inspection End.
NO
>> Perform diagnosis procedure. Refer to
ADP-67, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000010051765
Regarding Wiring Diagram information, refer to
1.
CHECK MIRROR SWITCH FUNCTION
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit
connector and ground.
2
13
LEFT
Yes
Other than above
No
3
RIGHT
Yes
Other than above
No
Monitor item
Condition
Status
MIR CON SW-UP/DN
Mirror switch (up/down)
Operate
ON
Release
OFF
MIR CON SW-RH/LH
Mirror switch (right/left)
Operate
ON
Release
OFF
ALJIA0397ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст